MDB6650AWW Maytag Dishwasher - Instructions

my husband took the bottom rack out, unscrewed it where there were screws, lifted up the unscrewed part, took the filter out,cleaned out any gunk, replaced the filter put the part back on, rescrewed it, put the rack back in and it works much better.

When I tried to remove the hold down screw for the impellar, the impellar broke in half. I actually did npt need to go this far with disassembly as the problem was with water being retained in the rinse arm assembly and stagnating. This was due to calcium buildup clogging the drain holes. Clearing the holes resolved the problem.

Just slide the old upper dishrack forward to the end. The stops on either slide must be removed . Only difficulty was getting the plastic stops to open up. We used a thin metal knivre to wedge into the opening.

Turned off the water. Disconnected the water supply line. Extracted 2 screws holding the dishwasher. Pulled out the dishwasher. Changed out the nylon spring link. Pushed the dishwasher back into place. Reattached the water line. Turned the water back on.

Spring linkage and postage about $15.00.
Savings on service call and parts about $175.00. What a deal. Thank you PartSelect.

da basket don't come with rections so you gota figer it out yor sef. I tride pullen the handle off and it work then I tride pushen it on the other basket and it work to. Then i tride swapen dem and it work so thats how ya doit

Took out the six Torx head screw out of the door inner liner. Lifted the liner off. The handle mechanism was easily repaired by allowing the old part to fall out and snapping the new one in. It took me longer to find my Torx screwdriver than to fix the handle.

Removed front access panel
Disconnected water supply
Pulled dishwasher out approximately 1 foot to gain access to spring linkage
Connected new spring linkage to spring, connected other end of spring linkage to door
Tested operation of door
Slid dishwasher back into place, reconnected water supply and front access panel

Removed 2 each screws from counter top. Pulled washer out 1'. Installed springs and linkage by hand with door closed. Push washer back reinstalled 2 screws.

Took off the lower front plastic piece and unscrewed the side panel to snap the new part in place then attached the spring to it.

I removed the four screws that hold the front kick plates on. Then, I removed the hose clamp (on the right side of the pump that secures the top shower hose assembly to the pump assembly. Then I pulled the dishwasher out, and pulled out the four black snap clips that hold the insulation in place. I then folded the insulation back and reached inside the dishwasher to disconnect the hose assembly. On the top spray arm is a nut that is easily removed without any special tools.
Be sure to save the rubber washer unless you order a new one along with the top shower hose.
Overall, an easy fix. Saved about $100.00 by doing it myself.

Looked into the problem, cleaned the sprayers out to no avail. Looked at drawings of dishwasher and noticed it had a filter. That seemed to be the next easiest thing to check. Removed the lower spray arm with channel locks, then removed the filter housing by removing 6 screw, removed old filter, replaced with new and reversed the above steps for re-assembly.

Piece of cake!

They just snapped in to place. Once I realized where they went. They are not the exact rollers needed but will do until I get the right ones. The rack will not come out as far as it should because of the difference. Other than that....easy.

Unscrewed the 2 screws securing the dishwasher to the counter. Unscrewed 2 front panels. Shut off water valve. Disconnected water intake. Pulled dishwasher out 5 inches. Removed broken spring, replaced it. Checked the door movement. Scrubbed the door rubber gasket of calcium deposits & debris. Replaced the Teflon tape on the water intake. Reconnected water hose. Opened water valve. Checked for leaks at the water intake location. Ran 1 dishwasher cycle again for leaks. Pushed the dishwasher back under the counter. Secured the 2 screws on top of the dishwasher to the counter. Reattached the 2 front panels and enjoyed a glass of wine.

I TOOK THE INSIDE PARTS ABOVE THE MOTOR APART AND TRIED TO CLEAN ALL THE CALCIUM AND MINERAL DEPOSITS THAT WERE PRVENTIN WATER FROM GETTING THROUGH. THERE WAS A LOT OF CALCIUM. MOST OF IT i WAS ABLE TO CLEAN AFTER A LOT OF SCRAPING AND SOAKING IN VINEGAR AND CLR. THE VINEGAR WAS THE MOST EFFECTIVE OF THE TWO.
i BROKE THE FILTER GUARD WHEN I TOOK IT APART. I SHOULD HAVE CHECKED ONL.INE BEFORE i START IT. THE SECONDARY FILTER ASSEMBLY WAS TO FAR GONE DUE TO MY MISHANDLNG AND HEAVY DEPOSITS INSIDE THE FILTERS. PUTTING IT BACK WITH THE NEW PARTS WAS EASY BUT I HAD TO SUBSITUTE SCREWS BECAUSE THE ORIGINAL ONES WOULD NO LONGER HOLD TWO PARTS TOGETHER. THE PARTS WERE LEAKING TO MUCH WATER. ONCE I HAD IT BACK TOGETHER THE SECOND TIME IT WORKED FINE. HOWEVER I HAD REALIZED THAT THE O-RING WAS NOT MISSING (MY BAD EYES DID NOT SEE IT IN PLACE AND SO I THOUGHT I HAD LOST IT). i EMAILED PARTS SELECT FOR A RETURN AUTHORIZATION BUT NEVER HEARD BACK FROM THEM. MAYBE I NEED TO GIVE THEM A FEW MOR DAYS. THE O-RING COST $3.76 AND MY WIFE WILL NOT BE HAPPY TIL I GET THAT BACK. PARTS SELECT DIAGRAM AND PARTS PHOTOS AND ANOTHER WEBSITE WERE A BIG HELP..

Never having repaired a dishwasher before, I disassembled everything I dared to until I found the root of the problem--part of the impeller had broken into several little bits. It wasn't apparent where the pieces came from, but the on-line diagrams and product photos helped. The broken impeller didn't want to come off the shaft, so I just crunched it up with a pair of vise grips. That seemed to be the gentlest solution for the pump bearings. The bits of impeller also took out the pump housing, which I could have ordered with the impeller had I been more observant. [insert four more days of washing by hand here] Inspect all parts for damage and clean out all stray chunks of food and plastic before reassembling!