KUDK30IVBS0 KitchenAid Dishwasher - Instructions

Partial disassembly determined thar the plastic handle was broken and a tensnioning spring was missing (had fallen out of reach within door) Ordered new replacement parts and received next day. Great delivery service. Installed in short time by removing four screws, disconnecting two wires and reversing procedures to reassemble. Finding parts on line was a great help and the delivery service was great,

I removed the dishwasher from under the counter. This took the bulk of the repair time along with disconnecting the water supply and electrical connection. I had enough slack in drain hoses that I could turn the dishwasher over to replace the motor. I was surprised that there was only one bolt that held the motor in place. I put the motor on, turned the dishwasher upright and slide it back unde the counter and began the long process ofreconnecting everything. I am sureit could have gone faster if I were younger and did not need glasses for close work. Start to finish took me four hours. This was the fourth time I have replaced motors in dishwashers of various makes.

First research then troubleshoot
Removed
1 Upper rack
2 Lower rack
3 Lower Wash Arm and Strainer Parts
4 Upper Wash and Rinse Parts
5 Accumulator assy.
6 Motor shield
7 Inlet protector (most difficult)
Noticed blade was broken off chopper assy.
Replaced chopper assy.
Runs and cleans like new.
Most difficult step was to remove Inlet protector
After removing two torx screws (#15) used small pry bar to lift inlet protector from position. Not easy to accomplish with hands alone. Inlet protector fits tightly into position.

Disconnected power to dishwasher. Removed water supply hose from inlet water valve.
Removed lower and upper racks. Removed Lower spray arm. Removed tube from pump tp top spinner. Pulled dishwasher from under cabinet (remember to tip to get back out!). Placed dishwasher on its back. Removed electrical connectors from water valve, main motor and drain motor. Removed drain hose from drain pump. Removed pump/motor assy by pulling out wedges and pushing assembly into dishwasher. Removed pump/motor assy from inside dishwasher. Cleaned out pump. Installed new chopper. Re-install pump/motor assy. Re-install driain pump hose. Re-connect the pumps and water valve electric connectors. Slide dishwasher near cabinet for re-install. Re-connect drain hose to dishwasher. Re-install dishwasher under cabinet.Reconnect water supply. Removed top spinner from tube. Installed new spinner onto tube. Re-install tube onto main pump (below lower spray arm). Clean out and re-install lower spray arm. Remove middle spray arm from top rack. Clean out spray arm. Re-install spray arm with a new gasket (gasket may have not been needed). Re-installed lower and top racks. Re-connect power supply. Position all three spray arms pointing towards the door to confirm they were turning. Tested dishwasher - confirmed fill, wash, and drain properly. Also confirmed that all three spray arms were turning. Machine is washing, draining and running great since!

I looked up the repair on youtube and followed along step by step.
I am a 64 year old female and the job was easier to do while watching a repairman than it would have been to read instructions.
The internet is great for some things!

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.

Major appliance retailer sent out a repairman to diagnose the issue with the washer. They determined the control board needed to be replaced. They wanted twice the price for the part plus an additional two hundred dollars to return and install. Total time to remove and replace the part less than fifteen minutes. I purchhas same issue. Once again the repair people, (another $80.00 for the second service call), say the control board muased the part from Part Select and installed myself. Washer st be replaced. I will purchase another dishwasher.

Replaced the switch, that did not fix it, but a new circuit card did

The repair would have been really easy if the parts replaced had come all in one...When you order a replacement handle they do not include the 2 small springs....
the springs are a bit hard to get on, but once they were in place everything went well. You need 2 people to assemble it.
One to hold the door and the guts of the electronics, and the other to install the handle.

I removed the old seal and carefully cleaned the track into which the seal was fixed. No tools other than some ordinary cleaning liquid, cloth and small wooden piece to swab out the track. Easy and quick. As a note here, I first used the incorrect schematic for the unit and ordered the wrong seal. However after receiving the wrong part, I made the correction and reordered. I did this over the phone as I needed instructions to return the part. The person taking my order and answering my questions was very helpful and I want to take this opportunity to thank her.

Pulled front panel and replaced door switch. Extremely easy but did not fix the problem.

I am a 61 year old woman and it took me a total of 2 min. max. Popped it into place and pushed in button that holds it..Taa Daa...perfect!

The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.

Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.