KUDK30IVBS0 KitchenAid Dishwasher - Instructions

Removed old part and replaced with new part

disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!

Removed old tine rows and replaced with the new parts. No tools were needed. Each was replaced one at a time so the old ones could serve as a model for how the new ones were inserted and attached. Not much more complicated than changing a light bulb. Parts appear to be good original equipment quality but quite pricy for these very simple pieces.

Snapped the new stops on. It took about 2 minutes.

removed 6 screws removed upper console of door and swapped out broken handle with new one. installed required spring and closed up console of door. real easy it took less than 15 minutes .

replaced the valve

Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit

removed rack
removed one screw
removed old seal
installed new seal
installed screw

Replacing the float switch was fairly easy and straight forward. removed old using adjustable wrench and replaced.

Replacing the door links was not difficult except I needed to pull the dishwasher out and had to disconnect the water line.
reconnecting the water line was the time consuming and frustrating part. Once that was hooked up and tested, i pushed the dishwasher back in place and all is good again.

Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher

I did not get to repair my dishwasher using the part supplied by Partselect.com. I pulled my dishwasher out and found that the connector had fallen of the capacitor during installation. Happy to say that I returned the part for a full refund minus the shipping. Have bought from them before, and will again

The door catch clearly was not acutating correctly when the door handle was depressed. I removed the 6 screws (star pattern, not phillips) from the top of the door to allow access to the door handle and catch. the door handle is made from a thin and poorly constructed plastic piece with two arms that attach to the body of the latch. The latch has an electrical switch that has two wires attached to it. Note the location of the wires before you disconnect them. remove the latch assembly and door handle together. Remove the damaged door handle. Note where the return springs are located on the handle and latch. Replace the new handle on the latch mechanism, attach the springs, put the complete mechanism in the door and replace the screws. Finding the problem took 5 minutes and the remove of the top of the door. Waited 4 days for the part, 10 minutes to install the new part and back in operation

Took the new one out of the box, and droped the new one in. . . . Simple, a child could have done it. . . . Amazing response to the part order. . . Arrived in 4-days. . . .