KUDS25SHWH1 KitchenAid Dishwasher - Instructions

Install too less that a minute. Fit perfectly.

I unscrewed the wash arm tube from the agitator, and then unhooked the plastice holders that held the arm tube, pulling those parts out of the dishwasher. I took the new (one piece!) wash arm tube in hand and then realized that I would have to cut the plastic holder in half because there was no way to get the new (1 piece) arm tube through the plastic holder. I cut the plastic holder in half, fit it around the arm tube, and super glued the holder back together, allowing it to dry for several hours just to be safe. After that, I simply screwed the entire thing back on, and we were good to go. It could not have been easier, except for the unexpectedness of have to cut the plastic holder. Saved us probably at least $100 worth of service call and parts.

removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.

1) Removed the two panels below the door.
2) Unscrewed the two screws holding the dishwasher to the upper cabinet facing.
3) Pulled dishwasher out 6-8 inches to gain access to springs located on the side.
4) Removed the broken spring.
5) Attached the new spring.
6) Openned and closed the door to make sure spring was tight enough.
7) Pushed dishwasher back in.
8) Rescrewed cabinet facing screws
9) Rescrewed floor panels.

Only problem was with ordering ... PartSelect part number is different than the FSP-Whirlpool part number. PartSelect should provide a cross-reference table if there is a difference between OEM number and PartSelect number.

First I read the other repair stories and knew it was a relatively easy repair. I removed the end caps on the front of the top dish rack and removed it for ease of access to the part. I then removed the two screws holding in the old part observing how it was positioned to make sure the new part was replaced in the same manner. I put the new part in place and screwed in place and replaced the dish rack. Everything is working just fine.

1 Screw 5 minutes thanks for the quick service will definitely use ya'll next time

My husband replaced the entire soap dispenser until in under 30 minutes. I stayed out of the room. :) I didn't hear any swearing, so I assume it went fairly well. Sorry that I can't give you detailed instructions. He didn't need a manual or any type of directions. I guess it was kind of obvious how to do it. Just be sure you turn off the power first.

I ordered the upper and lower rack replacements PLUS additional wheels and other attachments because I could not tell from the schematic on the website whether or not the smaller pieces came with the rack.

As it turned out, the racks came ready to install and all it took was a limber nephew to take out the old ones and put in the new. Now I have plenty of spare parts in my own inventory in case the wheels, etc. need replacing.

I feel guilty sending you this repair story because all I did was order the parts on your website and then conned my nephew into making the exchange.

The parts arrived very quickly and in good condition. In fact, the new racks are an improvement over the ones that came with the dishwasher originally. Ms. Susan McNutt was quite helpful in keeping me informed of the status of the part that was back-ordered. It was a pleasure dealing with PartSelect.com.

compared it to old rack. Parts snapped together in 5 minutes. the fit was good. Kit did not include the silverware baskets, or the fold down narrow shelf.

Unscrew the top bracket on basket of upper spray arm assembly. Remove entire upper spray arm assembly. Remove old spray arm. Install new spray arm and new supply tube being careful to align the upper bracket with slot on new spray arm and supply tube.

I removed the old wheel assemblies
(4 total holding 2 wheels each) with a slight prying with a screwdriver to
ease it off the rack. After the first one, the rest were a little easier.
The new ones had to "mate" a certain way and then just needed a push of the hand.

removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.

Old style tube was an assembly of 3 separate parts, so it could come apart to pass through the holder bracket easily. New style tube was a single piece. The moldings on either end are too large to slip through the holder bracket circular ring. Apparently, the newer style holder brackets have a slit or break in the ring. Not so with the older bracket I had. I merely cut my own slit at the top of the ring on my old bracket, allowing me to spread the ring wide enough to allow either end of the single-piece tube to pass through. There is very little pressure on the holder bracket ring - it's just a holster for the tube. So the slit does not affect performance. Job done in 30 min.

We unscrewed the old mount, and installed new mount, inserted screw and tightened. Waa-lah, that was all that needed to be done.

Bent back metal ears over door hinge pins, released door springs from door hinges. Lifted door off of hinges and replaced corner drain back seals and lower door seal.Still leaks so obviously I have another issue or the door seal is lousy quality. I've completed this project before and never had another issue for 6 years.