KDTM804EBS1 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dish rack slide arms losing ball bearings
Unscrewed mounting screws, pulled dishwasher out halfway, replaced arms, 4 screws each side .....very simple 30 min tops. Parts perfect and quick delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Highland Village, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Door Leveler Nylon Cord assy broke
It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MILLBURY, MA
- Parts Used:
- W11175771
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dishwasher wasn’t getting water.
I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from VAN BUREN TWP, MI
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
removed and installed cords with screw driver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from BIRMINGHAM, MI
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Dishwasher door had lost springback
1) Pull out dishwasher from under counter. 2) Disconnect spring located at the bottom on each side of dishwasher. 3) Using socket remove pulley wheels from each side at bottom. 4) Install new pulleys on each side. 5) Wind pulley cord around both wheels and attach to one end of the spring on each side. 6) Using pliers extend other spring end to lower frame of dishwasher on each side. 7) Open and close dishwasher door to test. 8) Replacement complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pauline from FERGUS FALLS, MN
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Broken plastic piece in door balance link kit
Watch video and followed instructions. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edna from WEST MONROE, LA
- Parts Used:
- WPW10653840
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
When cycling through it would stop up to 3 times & have to be restarted.
Replaced door latch
Was this instruction helpful to you?
Thank you for voting!
Top rack kept coming off the left slide track
I followed the video and even though my dishwasher was slightly different from the one shown, everything worked well. I was lucky that I had enough clearance to pull the dishwasher away from the countertop far enough to make the repair, without having to remove any dishwasher wiring below. I replaced both side tracks, even though only the left side was broken.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PORT LUDLOW, WA
- Parts Used:
- W11177741, WPW10653840
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Water leaking around door and latch mechanisim seems to have failed
Still not sure it is repaired. Still have water leakage around upper edge of door on control data panel. We just experienced an issue with the auto drain system, the first since door seal repair and door latch replacement???? Is the latching mechanism suppose to secure the door?
If so it isn't?
Not a great success story. A new washer may be in the cards
If so it isn't?
Not a great success story. A new washer may be in the cards
Was this instruction helpful to you?
Thank you for voting!
PartSelect Scammers
PartSelect intentionally shipped obsolete part that could not possibly fit a dishwasher. The part looked to be a rectangle door seal for a freezer/ref. You make it impossible to return the part. I find it interesting that you sent the correct install video and wrong part.
Suggestion: After you print a shipping label take a picture of the part and shipping label before it is boxed. The customer should not have to send you a picture of the wrong part and the serial number of the appliance for a refund. You did not need the serial number to ship it.
I will never use your company again William Dewberry
Suggestion: After you print a shipping label take a picture of the part and shipping label before it is boxed. The customer should not have to send you a picture of the wrong part and the serial number of the appliance for a refund. You did not need the serial number to ship it.
I will never use your company again William Dewberry
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eladio from LOGAN, OH
- Parts Used:
- WPW10538166
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Develeoped a leak on the bottom.
Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Des Moines, IA
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Dish washer was very smelly.
After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from KENT, OH
- Parts Used:
- W10861000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Worn out detergent dispenser
Total repair time after watching videos was 53 minutes. I estimate I saved between $200 to $300 by doing this myself. If you have any DIY skills, don't hesitate to replace the detergent dispenser yourself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from SICKLERVILLE, NJ
- Parts Used:
- 4317824
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Intermittent power loss
Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from ROLLA, MO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
installer from lowes di not do it right, forgot to put scew in, instead he used shims, as usuall no more installs from Lowes
followed directions, a kid could have done it,
Was this instruction helpful to you?
Thank you for voting!