KIDS42EPSS0 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeff from Medford, OR
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the tensioning cords snapped.
Very easy repair. Removed (front) bottom access panel. Removed two screws under caps on the inside front edges (one left, one right) of the DW. Slide DW forward (out of its recess) about one foot. R&R tensioning cord. Reassemble. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Yuma, AZ
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher door would fall open
Removed the two screws on top and slid the unit out until the spring area was exposed relaced the part and slid back in, it was so easy. The part needed came in a set so I now have a spare. Your rep was so helpful in identifying the needed part for me and the whole expense of parts and shipping was half of what a service call to identify the problem would have been, say nothing of what they would have charged for the part and installation. Thank you I am a lifelong customer now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LARRY from REDMOND, OR
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door Hinge Didn't Work, Door Fell Open Without Resistance
Unscrewed the brackets at top of frame to pull the dishwasher out. Hooked the spring back through the hole in the rear housing, hooked the front plastic piece to the door, wrapped the cord around the pulley wheels, streched the spring with a pair of pliers and hooked the other end of plastic to the spring. Very easy. While working also oiled the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Margate, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Door spring support broken
Removed 2 screws that attaches dishwasher to countertop. Turned off water, disconnected hose, pulled out dishwasher. Replaced plastic pulley system. Pushed dishwasher back, replaced hose, turned water on, replaced 2 screws. Job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Windham, VT
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door flopped open
Took off the front kick plate and the two screws holding the top to the counter, and then carefully pulled the machine out 3/4 of the way. Removed broken part, installed new part, tested movementof door, then pushed it all back into place, reinstalled screws to counter and bottom kick plate, did a test again to be sure it all worked, Poured another cup of coffee and put peanut butter on the english muffin, left for work. Any questions?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Edina, MN
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher door opened and closed abnormal force - lost counterbalance
Removed the two screws securing the lower access cover below dishwasher door and removed two upper mounting screws securing dishwasher to countertop. Grasped dishwasher near front feet and slid unit out of encloser approximately 12-14 inches. Removed broken balance link cable from attachment point on dishwaher door and from the balance spring. Removed existing balance link pulley/guide assembly from side of dishwasher frame and replaced with new assembly. Connected balance link cable to balance spring, then strung/wrapped new cable through and over pulley/guide and connected cable end to mounting connection on door frame. Completed same process for opposite side of dishwasher. Pushed/slid dishwaher back in to its original position, re-attached the two counter to dishwasher screws and finally reposition the lower front acess panel and secured it with the two screws previously removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from Evergreen, CO
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
the dishwasher door spring link broke.
First we removed the screws that held the dishwasher in place. After pulling the dishwasher out, we could see the spring lying on the ground. (Usually only one breaks at a time so you can see where it goes and how it is hooked up on the one still in place.) We removed the broken link, which is made of plastic and rope, then we hooked the link on the spring and rehooked the spring in the back of the dishwasher. The next step took two people, one person had to hold the spring with tension on it while the other manuvered it around the wheels and then hooked that end up. Push back the dishwasher and replace the screws that hold it in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Santa cruz, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
door spring broke
just remove screws and replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theeravut from Gilbert, AZ
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door drop open.
I only need to replace a piece of plastic that attach to spring hook up to dishwasher door, so I only utilized one part from the kit.
1. Removing the dishwasher from counter-top by unscrewed two screws.
2. Slide out the dishwasher out from counter-top space.
3. Took out the broken plastic part, and hook spring to new part.
4. Using plier to pull spring and attach the plastic part to the door.
5. Testing that the door is working okay, push the washer back in place and screw to secure.
1. Removing the dishwasher from counter-top by unscrewed two screws.
2. Slide out the dishwasher out from counter-top space.
3. Took out the broken plastic part, and hook spring to new part.
4. Using plier to pull spring and attach the plastic part to the door.
5. Testing that the door is working okay, push the washer back in place and screw to secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Newburgh, NY
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Door would not stayed closed enough for dishwasher to run through full cycle and door would just drop to the floor when opened!
When I received parts I was worried because they looked a bit different than what I had. Not to worry the parts worked perfectly and in less than 15 minutes I was back in business. Thanks Part Select
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- greg from oviedo, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
One balance broke on door
Removed two screws at top of dishwasher. _Pulled unit out. Repaired both balances and pushed unit back in. Secured the two screws and Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Morrisville, NC
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The door on the dishwasher drops open
Removed the bottom cover with the nut driver. Removed the two screws attaching the top of the dishwasher to the underside of the cabinet. With the wrench lowered the front of the dishwasher so that it would slide out of the cabinet. Once out the balance cables could be seen and were replaced. Attach the cable to the door, feed it around the new and improved bracket (part of the kit), attach to the spring and then attach the spring to the back of the lower rail. Repeat on the other side. Reinstall the dishwasher. This took longer than all the rest of the job due to the poor work done by the home builder's plumber in the original install. Replace the front cover and sound shield. All and all very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Fort Lauderdale, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door tension system failed.
Chronic problem with KitchenAid dishwasher -- the connection between the tensioning spring on each side and the dishwasher door are two cheap twine-and-plastic assemblies. Opening and closing the door stresses the twine, and eventually it breaks on one side or the other. The only way to fix it is to replace the twine-and-plastic assembly, which is really simple to do once the replacement part is received. Takes longer to pull the dishwasher out from under the counter than it does to replace the part. In seven years, this is the fifth time one of these parts has failed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from Lake Clarke Shores, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
String holding Dishwasher door in static position broke
Removed screws holding dishwasher to countertop and pulled dishwasher out about a foot from the cabinets. Spring had jumped out of position on one side where door opens and closes. String was broken. Used old string to thread new string onto pulley wheels. did not replace the wheels in the kit since they did not appear to be damaged.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Austin, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Rope break on the door balance system
Pulled the dishwasher out of the cabinet, set the rope with the plastic ends on the spring and lever for the door and pulled the spring into it's holder and returned the washer into the cabinet. I ordered the part on the 27 in the morning and it got here on the 28th in the afternoon. Local part store wanted $40.00 for the same kit and I got it from you at less than 25.00. I also got to skip the service fee which would probably be about 65 dollars.
Was this instruction helpful to you?
Thank you for voting!