KIDS42EPSS0 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kevin from Mustang, OK
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Door Balance Link Kit
Disconnect the water and power supply to the unit. Remove the kick plate with a screwdriver and pull the unit from under the counter far enough to expose both door lift springs. With the door closed and locked release the tenson on the spring and remove the cable latch from the spring.One of mine was broke so this only had to be done on one side. With a 5/16 nut driver remove the bolt that holds the guide pullys in place. This is where I learned the problem from the original instulation. There are three screw holes to adjust the amount of tension on the cable. Mine was set with the most tension which is what caused the cable to break. I installed the new cables in the reverse order from above with the least amount of tension. It still supports the door but with less strain on the spring and cables. Good Luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Safety Harbor, FL
- Parts Used:
- 8194001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Broken door balance link
Followed the virtual repairman instructions. They were
great! Good overall experience with the site and service.
great! Good overall experience with the site and service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from Laguna Woods, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
rope link broke.
pulled dish washer from under cabinet. let door down, removed old link kit, installed new rollers and ropes, pulled springs into place, and hooked into ropes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Riverview, MI
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door keep falling open.
Pulled out dishwasher. Found cord broken on one side. Replaced cord and other parts that came in kit. Replaced balance parts on both sides of door. Pushed dishwasher back in place. Door now opens and closes like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Hebron, CT
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door Balance Link Broken. (3rd time)
Removed the lower panel underneath the door close to the floor.then the two screws underneath the counter top. pulled dishwasher out enough to remove broken door balance link from the spring and door. I found the Video on the PartSelect page to be very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Ankeny, IA
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
One of the door balance cords broke
I watched the video on the website and proceeded with the repair. Easy Repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Evans City, PA
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
rope broke
repaired the same as utube video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from New Baltimore, MI
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
String and plastic connector failed
Removed dishwasher and connected the new link to spring and door arm. Reinstalled machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Chugiak, AK
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Broken line in door balance system
Removed old balance link lines and poorly designed roller system with new lines and improved design rollers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Monroe, LA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broken balance link cord...
Simple repair, detached 2 top screws and slid unit out far enough to access the rear springs, removed old balance kit and installed new. The replacement parts appear to have corrected some deficiencies in the OEM version and the instructional video made changeover easy. As an extra bonus, annoying long-term door squeak is history.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Los Angeles, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher door would fall down when unlatched
Identified first that the Door Balance Link Kit was required as opposed to a new spring - the springs are nearly indestructible, I don't see how the spring would ever fail before the link kit. The hardest part was sliding the dishwasher out - nut driver to remove the lower panel, removed the insulation under the dishwasher, then found the two plastic screw covers in the door frame. Under the screw covers are screws to attach to the cabinet frame - your installation may be different. Then I slid out the dishwasher.
The link kit consists of two roller assemblies and two links - basically a nylonish cable with a plastic eye-hook on one end and a longer hollow-rectangle kind of attachment on the other. I only used the links (the cable parts) for this repair.
Swapping the link kit took 2 minutes. Hook the spring on the frame that is parallel to the dishwasher front, attach the eye-hook to the spring, push the cord into the pulley system, and pull on the link with the spring to get the rectangular hook to loop over the door hook.
Sliding the dishwasher out and putting it back in took much longer than the actual part replacement, but it was still a quick repair. And now the door doesn't even squeak when it opens!
The link kit consists of two roller assemblies and two links - basically a nylonish cable with a plastic eye-hook on one end and a longer hollow-rectangle kind of attachment on the other. I only used the links (the cable parts) for this repair.
Swapping the link kit took 2 minutes. Hook the spring on the frame that is parallel to the dishwasher front, attach the eye-hook to the spring, push the cord into the pulley system, and pull on the link with the spring to get the rectangular hook to loop over the door hook.
Sliding the dishwasher out and putting it back in took much longer than the actual part replacement, but it was still a quick repair. And now the door doesn't even squeak when it opens!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from WOODLAND, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
spring holding the door closed became disconnected (cord broke)
I watched the video and followed the instructions. I was very impressed with the video and the entire process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WENDEL from MURFREESBORO, TN
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Nylon rope broke
Disconect electric, remove screws, re-suspend Nylon and plastic suspenders.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucio from Fort Worth, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
broken nylon cord door hinge.
The part came pronto. The actual repair was fairly easy, but pulling the dishwasher out it is another story. I replaced the water supply copper pipe by a flexible braided hose. It looks like this is a common problem for these dishwashers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VICTOR from Las Vegas, NV
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench (Adjustable)
Door would not work properly, it fell open
The part sent was differen in appearance than the original. After calling I was told it would work, and it did. It took 2 people to move the dishwasher out from counter since the levelor,s were a little rusty and it had to be lifted to spray the wd 40 on the screws before we could raise them to pull dishwasher out. We used directions and easily replaced the string pull. After checking the unbroken one we noticed it to was begining to wear out, so we replaced it as well. Good thing their was a pair of replacements. The repair was perfect and I was very pleased with the support.
Was this instruction helpful to you?
Thank you for voting!