Models > KIDS42EPSS0 > Instructions

KIDS42EPSS0 KitchenAid Dishwasher - Instructions

Jump to:

All Instructions for the KIDS42EPSS0
76 - 90 of 309
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Doug from Huntington Beach, CA
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Link (String) broke on one side of dishwasher. Causing the door to basically fall down when opened.
Removed the bottom cover plates.
Removed the screws holding in the dishwasher.
Removed old single moving roller and replaced with newly designed double rollers.
Installed link(string).
Replaced other side rollers and link.
Reinstalled dishwaser.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Armand from Westfield, MA
Parts Used:
8194001
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set
Door spring cable broke.
Shut off elec. and water. remove bottom plate and 2 screws holding the unit to the counter top.
disconect elec wires to unit and remove water line.
Pull unit out from counter and replace cable to spring the same way as the unbroken side.
Slide unit back and reverse hookup.
My only problem was that the part they sent me was about a 1/2" shorter the the original and the door is hard to open.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Rancho Cucamonga, CA
Parts Used:
8194001
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Dishwasher door 'spring' broke...heavy door would fall hard when opened.
First we removed the two screws up under the countertop that secured the dishwasher in place. Next we pulled the d/w out from under the counter, having to unplug the power cord and feeding the drain hose into the d/w cavity from under the kitchen sink to allow this. On each side, attached to a metal spring was a nylon cord with plastic attachments that ran through two plastic pullies/wheels. The plastic piece on one of the nylon cords had broken...only on one side, so we were able to just look at the 'good' side to see how to attach and string the repair part through again. We pushed the d/w back in, made sure the drain hose under the kitchen sink wasn't kinked by pulling it back under the sink from the d/w cavity, plugged it in, replaced the two securing screws and were done. The old cord running through the pullies had always creaked when the door was opened, so while the d/w was out, we coated it w/ WD40. Piece-of-cake!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leslie from AUSTIN, TX
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
door would fall or slam open, no tension to hold door open.
Unscrewed mounting screw at top and bottom of duahwasher, pulled out dishwasher could see the pully on one side had broken. installed new part put dishwasher back in place and rescrewed mounting screws.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lawrence from Tucson, AZ
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Door counterbalance cable broken
Remove two screws on retainer clips holding dishwasher to counter and pulled out dishwasher. Slide new nylon cord mounting clip into slot where old part is located, rethread the cord around pulleys and attach end to spring. Need pliers to pull and stretch spring. This was the hardest part of the job but not very difficult. Push dishwasher back into counter and replace the two screws into the hold down clips under counter top. Whole job took 20 minutes.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Caesar from Layton, UT
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken spring cord for door
First I removed the two screws holding the dishwasher in place. Then I pulled the dishwasher forward from under the counter about 2 feet, attached the new part to the spring and pulley, then pushed the dishwasher back into place and installed screws.
PartSelect was awesome! UPS delivered to the wrong address and Partselect took care of it IMMEDIATELY! I have ordered more parts from them and no problems. I would DEFINATELY recomend them!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from Boca Raton, FL
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
The cord that connects the door to a sprink broke.
Once the cord broke, the stainless steel door became very heavy (eventhough the other side cord/spring combo was intact). My order came within days. The repair kit came with two complete sets (left and right sides). The repair was simple. I used the unbroken side as a guide to fix the broken side. I used all parts from the kit. The part of the repair that required time was to disconnect the electric, plumbing and drain lines. In order to pull the diswasher from the cabinet. Just remember to turn the water back on when you are finished!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Don from Dana Point, CA
Parts Used:
8194001
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
One side of the door spring link was broken.
I've had to do this repair at least twice before over the last few years so I stand by my original assertion that the door "balance link kit" reflects very poor design. Well, maybe the design would be okay if the materials were not prone to breakage. However, a simpler spring-only mechanism would have been more reliable. The current design uses string embedded in plastic that latches to a hook area for both sides of the door (frame). The string is threaded around a hub and then to a spring that is in turn connected to the chassis at a rather distant point which also adds to the difficulty due to requiring greater access to the dishwasher sides. It would be much better if the repair could be done without necessitating removal of the entire unit from the cabinet cavity first. I noted that this time around there's been a redesign so that the hub is no longer a round fixed knob but now includes a rotatable wheel. So perhaps there'll now be less wear on the strings that with the prior design! -- D.A.D
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lance from Angels Camp, CA
Parts Used:
8194001
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
Door fell open - link broke
Remove power. Remove drain line from sink. Remove hot water line at connection. Remove 2 screws that hold dishwasher to countertop (on top). Pull dishwasher out. Find spring as it has shot to the back when the nylon cord link broke. Hook Spring back in. Attach cord loop end (hard plastic) to spring. Attach other end to door hook. Now stretch spring to loosen cord and slip around pully system. Push dishwasher back in and rehook all connections.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bruce from Chandler, AZ
Parts Used:
8194001
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
One side of the door balance link broke.
One side of the door balancer broke. I pulled out the dishwasher and made a really strong one out of wire rope and clamps. 2 weeks later it broke again, so I ordered the link kit. I received it in a couple of days. But when I pulled out the dishwasher to replace my broken part I discovered that the original part on the other side broke. I put one of the new parts on the broken side and left my part on the other. I want to see which one lasts the longest.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Nipomo, CA
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Counterbalance spring link broken
I removed the 2 screws that held the dishwasher under the counter. Pulled the dishwasher out and easily replaced the replacement link. I slid the dishwasher back under the counter and replaced the 2 screws. Everything now works as it should
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Clemmons, NC
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
broken link - plastic piece attached to string
The repair packet contained 2 links with new pulley plastic pieces. It said to replace all of the parts. I could see that the old plastic pulley part only used 1 pulley. They had re-engineered to add a second pulley.
Changed out parts with no issues.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Lynbrook, NY
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Cord that connects the counter balance spring broke
I used a screwdriver to remove the bottom panel and pulled out the appliance. Tools were not required for the rest of the repair. The left side was not broken so I just duplicated the arrangement with the new parts on the right. Hook the spring to the back of the chassis. Hook one end of the link cord onto the door and lace it through the pulley and guide. Pull the spring with one hand and hook the other end of the link cord onto the spring with the other. Push the appliance back in and replace the bottom panel. Done in 10 minutes.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Simon from Tustin, CA
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Broken link on one side of door
easy fix, well worth the time...figure I saved $200-300 by doing it myself....make sure you route the cord between the roller and the little guide finger...easy to miss and creat a friction point that will cut the cord more quickly....
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
steven from Woodland Hills, CA
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Dishwaser door spring link broke.
Ordered the parts online and had them at the house 3 days later. Pulled the dishwasher out and restrung the link/cord through the pulleys and then connected to the spring and then the spring to the back of the dishwasher.

Literally done in under 5 min if that. Very very easy. You can look at the other side to see how the cord goes through the pulleys.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KIDS42EPSS0
76 - 90 of 309