KIDS42EPSS0 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from Falls Curch, VA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Door would not stay up unless closed - broken door spring
Pulled out dishwasher to access the sides. Removed onld lines and then unscrewed pulley from frame using socket / nutdriver. Replaced pulleys with new units supplied in the kit and then threaded new lines onto door and springs. Repair complete in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LONGVIEW, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The dishwasher door wouldn't hold in any position but went all of the way open.
You said the repair was easy and would take around 5 minutes to perform. You were spot on and the instructional video really helped do the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JIMMY from ST GEORGE ISL, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
cord on balance mechanism broke.
pulled it out, saw 'pulley' was fine, and put cord on spring and puled it enough to hook it on other end.end after running cord around the 2 pulleys, as it was on the other side. push it back and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from ELGIN, IL
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Squeaky dishwasher door
Just like the video; remove the 2 nuts off the kick plate, remove the 2 screws under the counter, pull the unit out, ease the spring off the cable, nut drive the pully assembly's off, install the new ones, place new rope/cable from the door arms onto pullys, attach the spring, push the unit back into place, replace screws and the kick plate. Took 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WEST NEWFIELD, ME
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
spring cable end broke
followed your very well done video clip exactly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from METHUEN, MA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door became heavy on one side
Pulled dishwasher and removed existing springs and attached rope. Ordered the part needed and replaced it somewhat easily. There is a lot of tension because of the spring on the door. Once part was installed we were ready to use our dishwasher right away. Even though the rope was broke on only one side - we replaced both sides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Fairfax, VA
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Lanyard on one side of door broke, so sudden heavy door and hazard to others
Thank you for letting me share my repair experience with you.
I removed the two screws that hold the diswasher to the wooden cabinet. Lowered the leveling adjustment screws on bottom of unit, then slid out the diswasher from inside the cabinet.
Then ordered the new lanyard. Waited one week day and the order arrived via mail. It has two lanyars and new rotating pulley assemblies for both sides of the door. I loosened the bottom screw on the old pully assembly and refitted the new pulleys in same location. (very easy). I then refitted spring to back of unit (with blue line toward front), then fitted the lanyard to the spring. Pulled lanyard thru the pulley. Had to have nice wife connect the other side of the lanyard to the post as I extended the spring on the side of the unit. We completed same steps on other side of the unit. After completing the door lanyard repair, I slid the dishwasher in the cabinet, re-leveled the unit with the front adjustment screw, then incerted the cabinet screws into the wooden cabinet. I feel this was quite a savings to us. Thanks to nice individuals on the internet and partselect.com, who provided excellent service to me....and my family. I also can see the end result of my effort, which is a nice feeling.
Thank you.
I removed the two screws that hold the diswasher to the wooden cabinet. Lowered the leveling adjustment screws on bottom of unit, then slid out the diswasher from inside the cabinet.
Then ordered the new lanyard. Waited one week day and the order arrived via mail. It has two lanyars and new rotating pulley assemblies for both sides of the door. I loosened the bottom screw on the old pully assembly and refitted the new pulleys in same location. (very easy). I then refitted spring to back of unit (with blue line toward front), then fitted the lanyard to the spring. Pulled lanyard thru the pulley. Had to have nice wife connect the other side of the lanyard to the post as I extended the spring on the side of the unit. We completed same steps on other side of the unit. After completing the door lanyard repair, I slid the dishwasher in the cabinet, re-leveled the unit with the front adjustment screw, then incerted the cabinet screws into the wooden cabinet. I feel this was quite a savings to us. Thanks to nice individuals on the internet and partselect.com, who provided excellent service to me....and my family. I also can see the end result of my effort, which is a nice feeling.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Petaluma, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No spring tension to dishwasher door.
After pulling the dishwasher out of the cabinet (2 screws held brackets to the underside of the counter - accessible when the door is open), I removed the broken link pieces, re-attached the springs and routed the link line around the pulleys. No need to re-set the spring tension as it was adjusted properly.
Was able to download a PDF manual from Sears for the dishwasher, so had the necessary information in the event adjustments were necessary.
I bought spare links as the dishwasher was less than 3 years old, and I expect them to fail again.
Was able to download a PDF manual from Sears for the dishwasher, so had the necessary information in the event adjustments were necessary.
I bought spare links as the dishwasher was less than 3 years old, and I expect them to fail again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sophie from Brooklyn, NY
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door got very heavy and wouldn't support itself
Removed 2 screws that held unit under counter. Slid diswasher out about half way; reattached metal spring in back and removed broken string. Attached replacement string to spring and threaded through wheels (copying other side), then attached string to door. Tada! Done. Will never pay a call-out fee again (for this problem anyway...)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Manhattan Beach, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Door counter-weight link broke
Followed the parts list diagram and confirmed with the link on the other side of door. Hooked the plastic attachment to the door, threaded the string around the plastic pulleys, attached the spring and mount it to the back of the dishwasher. that was it! Very easy to do. Hardest part was sliding the dishwasher out and in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Mansfield, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door pulley rope broke
Turned off power to dishwasher.
Removed screws from dishwasher retaining clips.
Pulled out dishwasher.
Removed broken rope.
Installed replacement and put everything back together.
Very easy repair. The spring is very strong and extra hand can be helpful, but not required.
Removed screws from dishwasher retaining clips.
Pulled out dishwasher.
Removed broken rope.
Installed replacement and put everything back together.
Very easy repair. The spring is very strong and extra hand can be helpful, but not required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kimberly from north palm beach, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
dishwasher door became very heavy to open and would not spring closed
First I turned off the water and power to the dishwasher.I removed the two screws on the front bottom cover plate, removed the plate. Removed the two nuts and bolts holding the dishwasher in place between the cabinets. Then I pulled the dishwasher out about 6 to 7 inches so I could see the spring, pulley and rope connections. Then I saw the rope on the right side of the door bottom had pulled through the connector. I ordered the part and next day delivery was great.(excellent service). The repair kit comes with both sides parts but I only needed one(for now). I reconnected spring to rope connector and threaded through pulley and to the door and job was done. A little difficult stretching spring so I put a long piece of wire to hold spring tight while connecting to rope but I worked out great. My husband said "great job, honey". I saved a $150 repairman bill....now I might go shopping (ha ha) Kim
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Sugarland, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door balance - the nylon cord broke
Received the part. No instructions came with it. Luckily it was pretty simple to figure out. i removed the appliance from under the counter, saw how the part was attached on the other side and simply replaced the other side that was broken. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Englewood, CO
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
broken door tension spring mechanism
Disconnect top screws
Pull dishwasher out halfway
Notice how the other side is connected
Thread cord, use pliers to pull spring to connect.
Pull dishwasher out halfway
Notice how the other side is connected
Thread cord, use pliers to pull spring to connect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angelo from East Williston, NY
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Pulley Cable broke on one side of dishwasher and the door was no longer supported when opened
The repair itself was relatively easy. I basically only had to remove the two screws that were securing the diswasher to the cabinetry, disconnected the water line and extended the diswasher out approximately 10 inches. I then replaced the part by hooking the new cable assembly to the spring and using pliers expanded the spring so I could snake the other end of the cable through the pulleys and attach it to the door. The otherside was my guide. This part should be modified to replace the two plastic ends with metal counterparts. This would allow the part to have a longer life especially in my case since the plastic end broke and not the cable itself.
Was this instruction helpful to you?
Thank you for voting!