KUDK03CTSS0 KitchenAid Dishwasher - Instructions

Took stop off end of track by smooshing spreader things together with butter knife, so they would fit through holes.
Maneuvered wheel on track and clip on rack. Put the stop back on.

Switched circuit breaker off.
Removed kick panel.
Removed the dishwasher from counter.
Disconnected drain hose from the pee trap.
Disconnected drain hose from pump.
Installed new drain hose.
Reinstalled dishwasher in counter.
Connected hose at the pee trap.
Turned power back on. test for leaks by running a cycle.
Reinstalled kick panel.

First let me tell you I am not a "handyman". I am a 50 year old housewife who was determined not to shell out $$$ if I could help it. I researched on the internet what could be the problem...it was more than likely the chopper assembly. I found a youtube video that showed how to get to the chopper assembly. So I removed the racks by dislodging the end clips. Next I took the bottom tub sprayer off by holding the middle with my fingers and turning the blade counter clockwise. Next, I unscrewed the line that ran in the back and up to the top sprayer (I only removed the one screw so I could slide it to the right slightly so I could remove it from the connector at the bottom and it revealed four screws that needed to come out of the mesh cover. After removing that there is one more screw that comes out of the shroud that covers the chopper assembly. I cleaned the area removed the chopper assembly (totally gunked up) and replaced it with the new one I purchased here...(lightening fast shipping btw!!...Yea! for PartsSelect.com....you guys rock!) I checked for gunk in the rubber valve assembly, super easy to remove/replace. Vacuumed standing water with my shop vac to get any errant noodles and food bits and reassembled all of the housing and lines in reverse order. Before I ran my dishwasher I put some clean water in the bottom...just poured about 32 oz in. Whether you need to or not....I don't know but figured it wouldn't hurt. IT WORKED LIKE A CHAMP! Super clean dishes again!! I felt so empowered and the whole thing cost me less than 20 bucks! Listen ladies....and men....this is super easy....If I can do it....any one can!

This was an easy repair. The leak was around the solenoid of the inlet valve and thus the assembly needed replacement. Turn off the water. Take the screws that secure it to the cabinet out. Pull the dishwasher out where you can tip it on its side. (you might get someone to help you hold it tipped. Disconnect the water line (copper) and the inlet hose (just clipped on)and the electric connection.
Take one screw out that holds the valve assembly in place and remove the valve assembly.
Put the new assembly in as the reverse procedure. Make sure to use plumbing tape on the threads to the copper water connection so that you wont have a drip leak when its tightened.

My dishwasher motor was getting very noisy lately and finally died altogether. (the fwd bearing and seals had worn out. There was a small pile of what looked like white sand under the motor from the wear) I removed the dishwasher from the counter after turning off the power at the breaker box. I then turned the dishwasher on its side. The pump motor is removed by first removing the electrical connector, then loosening the retaining bolt and twisting the motor counterclockwise about a quarter turn. The gasket required a little force to become unseated from the housing but not to bad. Wiggle and pull! Be sure to take a look at the alignment at this point to facilitate reinstallation.To install the new motor, align the mark on the impeller(small delta) with the mark on the motor. Insert Motor into housing and turn clockwise one quarter turn till retaining bolt hole is aligned. Install retaining bolt. Be sure to note the position of the stainless steel screen where you insert the motor. Place it back in position before installing the pump if it is disturbed. I lubed the oring with vaseline prior to install also. The new oring was diffrent and did not feel very tight when i installed , but there were no leaks and the dishwasher is running like new. Partselect had the part at my door the next day with no upgrade in shipping charges and I will use them in the future. This forum helped me choose them and made the task easier to do. Hope this helps you as well.

After unscrewing the dishwasher, I pulled out the washer, I saw that the springs were attached just by strings that were broken... I just used the strings from an old lanyard, retied everything, and did not need the springs! works well!

Very easy to install the new B Metal Fuse. Removed torx head screws holding the outer door panel on the dish washer. Removed the fuse and two wires connected to the fuse. Inserted the new fuse in the holder and plugged the two wire connectors back
on. Installed the outer door panel back on, turned the breaker back and the machine powered back up. Very easy install and saved a service call. Total repair cost $24

Checked grinder and cleaned it several times, adjusted blades. Dishes would be clean for approx. 6 cycles, then would not clean. Placed dishwasher on its front and removed the motor. Removed grinder and impeller which I found to be worn so that the blades would not turn on the grinder which caused it to collect food particles. The impeller locks in easily.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

open dishwasher door, use torx socket and ratchet to remove 6 screws. Pull down wash options face, find the bi-metal fuse. Used the directions in the package to replace. popped old fuse out of electrical board, Cut 2 wires, stripped said wires, attached stripped wires in housing on new part, tightened the 2 screws where new wires attach, popped new fuse in electrical board. Reattached face. Very simple and easy to do. Did not fix the problem. Had to get the electrical board that the bi-metal fuse is snapped into. Very easy for someone that has worked on vehicles or electrical things before. If no experience, then I would say it is still easy as long as you follow the directions taht comes with the part. It has pictures as well.

Popped out old wheel housing. Popped in replacement with a little help from a flathead screwdriver. Easy.

To empty the water in the dishwater basin, I pushed the cancel button and closed the door. I then turned the electrical breaker to the off position that supplies electricity to the dishwasher. I confirmed the power was off by attempting to start the dishwaser. I removed the metal plate between the dishwater door and the floor by removing the two screws. I removed the two screws that connect the top of the dishwasher to the underside of the countertop. I shut the water valve that supplies hot water to the dishwasher (mine was located under the sink). I disconnected the drain hose (plastic) by using pliers to loosen the clamp the holds the hose on the outlet of the drain pump (drain pump is much smaller than the pump that needed replacement). A towell is handy to soak up the water that comes out the hoses. I loosened the nut on the water supply hose (this was difficult because of lack of room)using a wrench and pliers. I opened the door on the metal box that houses the wire nuts for the electrical connection to dishwater, and I removed the wire nuts and the screw for the ground wire. Once the white, black, and gound wires were disconnected, I could pull the dishwater out. I also had to pull the drain hose out from the clips on the side of the washer to pull the dishwasher out into the middle of the kitchen floor. I flipped the dishwasher on its back. I removed the single bolt that held the broken pump motor to the dishwasher, and then the motor twisted counterclockwise and I pulled it out. The pump shaft would not turn freely with my pliers, so I knew the motor was broken. I removed the pump end (impeller) from the dishwasher by tapping it with my screwdriver. The impeller end came out along with a metal screen. The metal screen was 50% plugged, so I cleaned it and put it back in place. I wet the gasket on the new pump motor and slid it back in place while rotating clockwise and locking it in place with the tabs. I replaced the bolt that holds the motor in place and reversed the repair procedure to re-install the dishwasher. Be sure to run the dishwasher and look for any leaks. The last step is to replace the metal plate between the floor and door. While I had the dishwasher pulled out, I discovered another problem with the pulleys and strings that prevent the heavy door from flopping down, but I won't include this repair. The pump and motor must have been failing for some time because the dishwasher is much quieter now and the dishwasher is much faster. I am sure the plugged screen didn't help either.

I shut off the power to the dishwasher, then I removed the front panel under the door. On the right side just behind the electrical box there are two wires going up to the hi-limit thermostat, (you may need a small mirror to see it), remove one screw that is holding the thermostat bracket, unplug the wires from the old thermostat and install new one. Screw bracket and thermostat back to the underside of the dishwasher, reinstall the front panel, turn on the power, done.

To replace the soap dispenser you need to take off the front of the door, which requires removing about 12 torx screws - of 2 different lenghths (so keep track). Then the soap dispenser is held in place with 6 very small 4mm hex screws (why they used these instead of normal phillips??). Both my hex sets stopped at 5mm, so I had to go get one. Tool has to be narrow (not one that is flared) because the clearance between the screws and the unit is very tight. There is one small two-wire connector with a press-in connector that at first looked hard to pry off, but just grab it with channel-lock and it will just come off. Remember which way the wires are facing (ie. up or down). Be sure to note how the vinyl flap (that covers the back of the dispenser) attaches, then pull out the old one. Once the new one is in, the hardest part is putting the door cover back on. I'd advise having an extra set of hands. Made it much easier.

Pulled dishwasher out from under counter. Relaced cord with plastic hook attaching spring to door. Very easy.

Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.

Delivered in 1 day. Fantastic. Highly recommend