KUDK03CTSS0 KitchenAid Dishwasher - Instructions

Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

that there is 90% of the repair made easy when you have the correct part. there is no better then direct replacement parts. the repair was self explanitory. one screw, two lines, lock in place, done. thanks for having the correct parts,that is what makes a job simple.

Removed old seal, cleaned track, applied adhesive for new seal, seated new seal in track, closed door for 24 hours to allow adhesive to cure, then used dishwasher without difficulty. An easy repair.

Take 10 lower star srews from inside of door (5 per/side) that hold on front. Remove front door panel. Remove 6 screws in detergent dispenser and replace.

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

I removed the dishwasher from under the cabinet. This is what took the most time. Before removing the dishwasher from under the cabinet I disconnected the drain cable to remove all the water from unit. After removing the dishwasher I tipped the unit on its left side. The motor/pump assembly is held in with one screw. After removing this screw the pump/motor assembly comes out with a 1/8 turn counter clock wise. The replacement pump/motor assembly was put back in in reverse order. After the pump/motor assembly was replaced I replaced the door balance cable kit on the right side of the unit. Next I tipped the unit on to its right side and replace the left balance cable kit. After this all that was left was to return the unit back under the cabinet and hook up the water supply line, the drain line, and the power.

After reading other posts I opened the dishwasher door put a support underneath it. Knowing that all the screws were not the same I carefully unscrewed them and placed them on a towel in order of extraction. After all the screws were taken out, I lifted the door up gently and lifted it out of its place and put it aside. Now I could see the hex screws holding in the soap dispenser. I then unscrewed the screws and place the frame aside. Next I gently pulled the electrical connector to the dispensing unit off. After locating a snap tab on top on the left hand side and one underneath on the right hand side, I gently lifted the tab and the dispenser unit moved slightly forward. After gently prying the lower tab on the right hand side the dispensing unit was loose. I just reversed the process to put things back together. I was not necessary to have any help taking things apart but it was very helpful having a second set of hands when we put it back together. Lining up the screws for the door was much easier with two people. After installation, I started the dishwasher to check for leaks. Everything was fine. Very satisfied to be able to repair/replace this unit without calling a tech. If you can change a spark plug on a lawnmower you can replace a soap dispenser on a dishwasher such as mine. Very quick delivery from parts source. Thank you.

Soap dispenser unit could have been repaired by pushing the plastic arm back home and adding two drops of instant glue to keep the plastic shaft in proper place. Didn't need to purchage a new unit.

This kit comes with the link cords and the balance wheels. I only needed the cords. I undid the set screws under the counter edge and slid the Dishwasher out from under the counter. One of the links had a broken cord and the spring had snapped to the very back of the space and was a bit hard to find. I used the good side as a guide to see how to thread the cord correctly. I did not replace the wheels since they appeared to be in good shape and looked like they might be a bit more difficult to replace than just the cord. For a second I thought I had ordered the wrong part because the new cord's attachment point at the hinge did not look exactly like the originals but the new design worked just like the original. I did need one other person to help stretch the spring and hold the door in the best position so I could attach the cord to the hinge. It's working perfectly now and I saved the wheels in case I need them later.

The upper spinner was laying in the top washer basket. I went online but no help was avaiable. Went to store where we purchased dishwasher and they gave me part number to order but not online I had to call to order. Part arrived in about three days. I took two screws loose on the top of dishwasher removed broke retainer to put new retainer in but I drop it into dishwasher so you have to me very careful
so I tried to order just the retainer but is not sold by it self. Had to order whole new kit. Other than that it is easy dishwasher runs like a new one.

Remove front door panel, replace B-metal fuse.

The first thing I did to repair my diswasher was call a repair company. They wanted $175.00 just to look at it, so I scheduled an appointment. Then, I did an internet search for dishwasher repair. I learned about bi-metal fuses, and how to check them. I found my bi-metal fuse was bad, so I ordered a new one through parts select. My part arrived in two days. I installed it easily, and the dishwasher worked. Finally, I canceled the repair appointment.

Replace motor/pump assembly

I watched the video and this was the easiest repair ever. Took longer to disconnect and reinstall than it did to change out the pump. Highly recommended watching the video

I peeled off the old seal and replaced with the new seal. The instructions were clear and easy to follow, however the new seal made the door not stay closed as the friction catch at the top was no strong enough to overcome the tension of the door closed with the new seal.

There were explicit instructions on the way the seal was to work with the sealed edge spreading into the tub area as the door closed. I was very careful to follow those instructions and made sure to seat the seal carefully. After I reinstalled the seal three times to see if I could get it to seat properly, as a last ditch effort I reversed the seal to the opposite way the instructions indicated and it worked with the door closing properly and the seal didn't leak.

Based on looking at the old seal and how it was originally installed, I actually think the seal was out of spec for the unit. However, if it isn't leaking that is what it's all about so we will see how long it holds.