Models > 66516517990 > Instructions

66516517990 Kenmore Dishwasher - Instructions

Jump to:

All Instructions for the 66516517990
121 - 135 of 736
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Charles from Hopkins, MN
Parts Used:
WP8539324, WP3378186
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Broken mount caused dishwasher to shoot water against door, caused leaking
Removed broker washer arm mount with screwdriver and replaced. New parts clipped right on to upper rack, no tools needed. Didn't really need to replace the tube holder but it was brittle so I put it in the order.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ronald from VAN BUREN TWP, MI
Parts Used:
4317824
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
none
removed and installed cords with screw driver
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jonathan from DOWNS, KS
Parts Used:
4317824
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jose from Coolidge, AZ
Parts Used:
WP3378134
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Cap was missing/lost.
Easy fix. It’s a screw on by hand piece.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tim from Lock Haven, PA
Parts Used:
WPW10509257
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
door seal leak
Removed seal from door with flat head screwdriver, replaced with new seal. Actually took longer to get out of the box rather than to fix!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Terri from Pleasanton, CA
Parts Used:
WP8268816
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Flex tines wouldn't remain up due to broken clips.
First, I removed the tines which were still connected to the top rack by the unbroken parts of 3 clips. (The part of the clip which is subject to breakage is the top, where it allows the tines to be clipped up or released and laid down.) I left the broken clips on the rack as a guide to where to install the new ones. I then attached the new clips to the tines, which is like assembling a puzzle. It would be helpful to replace one clip before all 3 break, so you have an illustration, but it's fairly easy to figure out how to attach the clip as long as you realize the tines need to be released and folded down, or clipped in the up position. With all 3 clips attached to the tines, simply pop the broken clips off the rack and attach the tines to the rack with the new clips. I appreciate the advice from the users who warned against breaking the clips with a tool. It's not really necessary to soak them in hot water. My advice is to use only fingers for installation. Brute force is not necessary... just position and pinch.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
james from encinitas, CA
Parts Used:
WP3376846
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
washer arm wound rotate, bearing was worn.
required NO tools,

just unscrew the large thumb screw, and replace the washer arm bearing!

problem solved like that!

maybe a 5 min job. part was a perfect match.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Maria from New York, NY
Parts Used:
WP9742946, WP9742945, WP3376846
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The Nut was broken in half, wash arm worned out
I just had to unscrew the old nut and screw the new one and install the new wash arm bearing ring.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Harvard, IL
Parts Used:
WP9742946, WP9742945
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken Wash Arn Retainer Nut
Screwed on a new one. The real story is getting the part. I called about noon one day and the part was dropped off at my house by FedEx the next day. Unbelievable. And the lady I talked to found the part number etc that I needed in a few minutes. Great service at a fair price.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Fred from SICKLERVILLE, NJ
Parts Used:
4317824
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Intermittent power loss
Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Althea from Vancouver, WA
Parts Used:
WPW10509257
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Leaking Dishwasher
I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Tulsa, OK
Parts Used:
WP9742946, WP3376846
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
lower spray bar bearing rings
Removed spray bar by removing the plastic finger thumb screw and replace as shown by you web page. Very simple.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stanley from West Sand Lake, NY
Parts Used:
WP8268816, WP3377464
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken tinerow clips left cup rack "flapping -in-the-breeze".
Removed top rack from dishwasher, removed broken clips - 2 out of three were snapped, and replaced them with FOUR - spaced more regularly to take the stress since this is the second time 2 out of the 3 had snapped. Simple job; rack swings well now, folds easily and clips securely upright.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
victor from cheektowaga, NY
Parts Used:
675808
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Original rubber extension tube had worn where it connects to the rotary fitting under the upper basket
First I removed the upper basket from the dishwasher by taking off the end clips from the right and left hand slides. The clips are removed by prying them gently upward with a screwdriver.

Second I removed the old spray arm assembly by slipping the old tube off of the rotary fitting.

Third I removed the center screw from the rotary fitting which holds the upper spary arm in place. I also removed the small plastic piece (block) which is clipped to the wire basket.

Fourth I installed the new spray arm assembly making sure to orient the plastic spacer block so that the spray arm rotates freely. The spacer block clips on the wire tray and the assembly is held in place with a single screw.

The new assembly includes a one piece extension tube and end funnel so it is really easy to install.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nancy from Nashville, TN
Parts Used:
WP3379369
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The upper Water dispenser fell apart
It was very simple, the repair took less than 5 minutes start to finish. I removed the top dish rack, took out two screws and the broken part slipped right off the water feed tube. I slipped the new upper wash assembly on the end of the tube and replaced one screw. My dishwasher is an older model and the new part only has a hole for one screw but I cannot tell any difference in stability or performance. I put the top rack back on and the dishwasher is as good as before.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 66516517990
121 - 135 of 736