665KUDS23HBAL0 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- phillip from new holland, PA
- Parts Used:
- WP9741049
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the filterscreen in the bottom of DW was full of holes
I removed the rotor and replaced the old filter with the new and viola ! completed !
Was this instruction helpful to you?
Thank you for voting!
broken roller weels on bottom dish rack
I simply removed the broken wheel brackets and snapped new ones on. then the wheel just sliped on. It took some good hand strength.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- douglas from stocholm, NJ
- Parts Used:
- WP9743413
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench set
water not going into dishwasher
While replacing the water valve I broke the float switch. Ordered the switch....it was here in 2 days. Great service! Will use this company again....I hope not all that much. lol
I am a retired Sears service tech, but not a dishwaher tech.
Love Parts Select!
Thanks guys,
Doug
I am a retired Sears service tech, but not a dishwaher tech.
Love Parts Select!
Thanks guys,
Doug
Was this instruction helpful to you?
Thank you for voting!
Old float stem had fine thread new one had corse and did not supply nut so had to use old one over.
put new switch and new gasket on old float stem with old nut. but it still overflows about 1/2 cup of water through stem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eddy from Greenville, CA
- Parts Used:
- 4169400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
no problem---color change
unscrewed 4 screws on top panel and 2 on bottom panel... real easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emerson from Denver, CO
- Parts Used:
- 675806
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Wrench (Adjustable)
the center screw in the impeller was too thigh, and the adjustable wrench wont hold the impeller still
I could not find a 90 degrees 1 inch car wrench and by them the impeller head wish is plastic was all run down so nothing will hold it, finally, I heat up a flat screw driver and cut the impeller near the head whit the help of a hammer , and them I could grab it with a pressure wrench and loose the screw up. finally the fix when fine and is working good. the parts are just the ones I need it. Thank you.
Was this instruction helpful to you?
Thank you for voting!
Ordered axles to replace several originals which had broken.
The installation video is excellent. What should have been a simple fix proved to be difficult for me. Perhaps a function of not enough hand strength to "snap" the axles in place. After trying to use a screwdriver to pry open a side enough to slide on and soaking in hot water to make the axles more pliable -- neither of which worked -- I turned the rack on its side, inserted the axle in the opening and then stepped on it. Voila! That worked beautifully and the next two were easy using the "stand-on-it" method. For anyone with a similar issue as far as hand strength, I recommend this method.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Ballwin, MO
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Dishwasher will not drain.
Turned off electric to machine.Removed water with shop vac, Removed lower panel, removed drain hose from check valve and garbage disposal. using shop vac removed blockage from drain hose. Reconnected hose turned on electric cycled dishwasher. Didn't work. Turned off electric, removed water, removed basket, sprayer arm, pump cover, used a six point deep socket to hold impeller while removing 1/4 in. screw. Removed the impeller and found the problem.The lower impeller shaft is broke. removed separator, chopper blade and spring, removed pump cover and broken drain impeller and lower seal. Cleaned all old parts and installed new drain pump kit. Replaced spray arm , basket . Turned electric on, cycled the machine one time. Checked for leaks, replaced lower panels. Put away tools. Your video was very helpful. Your service was great. I received the parts the next day after ordering them. thank you. thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- omar from seattle, WA
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
The motor was spinning freely and not pumping out the water.
We followed the excellent video until we couldn't remove the outlet impeller because the motor shaft was not being held by the failed impeller. We drilled small holes around the impeller shaft until we could break off the upper part of the pump shell. Then we could hold the motor shaft with a vice-grip pliers by squeezing the shaft of the remaing impeller piece. We then removed the retaining screw and the rest of the impeller. Then evrything went well by following the video. There was still a bit of doubt because we discarded more old parts then expected but the machine now works well and we see no leaks.
Was this instruction helpful to you?
Thank you for voting!
bottom tray had come off
I took off all the old axils and put new ones on,and then I slide the wheels on and That was all is to it. EASY!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruby from Saint Marys, GA
- Parts Used:
- 675238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
missing part
screw it in then hook up the hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fernando from El Paso, TX
- Parts Used:
- 675806
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher making a noise (lower area)
I reviewed your video and followed the steps, I appreciate the video. I used the tools described in the video; it was a simple process. Thank you Parts Select. .
Was this instruction helpful to you?
Thank you for voting!
wheels on bottom drawer broken
Took out drawer. Replaced broken/missing wheels and axles. Used pliers to snap them together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sarah from MELBOURNE, FL
- Parts Used:
- 4162321
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
the plastic roller axles had become brittle, and were breaking, dislodging the little wheels that guide the lower rack in and out of the unit smoothly
broke off the remaining roller axles, pushed the new roller axles into place, then snapped the little wheels onto new axles. I FELT LIKE WONDER-WOMAN, FIXING MY OWN DISHWASHER!!!
Was this instruction helpful to you?
Thank you for voting!