665KUDS23HBAL0 Kenmore Dishwasher - Instructions

I tried going online to get some diagnostic help and never found a site that had a step by step help plan. I then did a little reading on different sites, to eliminate and perhaps diagnose my problem I use epoxy to glue the impeller(which spun freely) to the screw and it held long enough for me to see how it worked. I surfed sites to find the least expensive drain and wash impeller kit. One site had a cheaper price but I chose Parts Select because of the shipping so the end result was the best results for me. I am not sure but the estimated time was 1.7 or 1.8 days delivery that I did not believe would happen. When I received the parts and did the repair my final time from ordering was less than a day and a half. I could not have done the job myself without the video because the parts were very different. My biggest obstacle, other than my ignorance, was some sort of chemical on the screw that would not allow me to loosen it. I used a dremel to cut the head off and then a torch to heat the stub so I could remove it. After I received the kit I saw a chemical on the screw threads so online research told me heat loosens the chemical. My dishwasher is around 25 years old,I have worked on it three times now and replacing the impeller was the most difficult task to date. Should it last and develop another problem I will go to parts select first and start my quest.

followed the basic instructions / diagram supplied, however the impeller was fused to the shaft. Used high speed cutter to remove old impeller and sandpaper to clean up shaft.

My dishwasher quit working the week before Thanksgiving, and to say the least, my wife was quite concerned. I did not know what was wrong, until I found the info on this website, including a how to repair video. I watched the repair video on the website when I ordered the parts. Other than my wash arm being different from what was shown in the video, it went exactly as shown in the video. I'm glad that the video, and the bag with the parts told me that there are fewer parts than originally were installed on the original. The parts looked like they had been redesigned a little, and were easier to assemble. Overall, I will be getting any repair parts I need for other appliance repairs in the future from here. Thank you for making this experience as easy as it was.

Dishwasher Stopped then only made a humming noise. Started with the Video on your site and it was quite helpful. I had trouble holding the drain impeller with the wrench. Used a drill to bore holes around the center and then broke the outer ring off to get a good hold on the center. Then was able to remove the bolt. The rest of the repair was easy. Something had caught the chopper blade and unraveled the spring. Replaced all the parts and it is working fine now.

Ordered the drain and wash impeller/chopper kit, which I received in 2 days. Great service. I watched the video on how to install the parts and the video was very clear and made the job seem easy. And it was easy, except for getting the impeller screw out. The impeller top was very brittle and pieces kept breaking off when trying to hold it with the adjustable wrench. Robo Grips didn't work any better. The only thing that finally got that screw out was a long handled socket wrench with an extension. You need the extra leverage if the screw is really stuck. Also note that the balls are definitely in the wrong place in the video. You need to remove them when doing the repair, then drop them back into the hole in the gasket/seal cover for the impeller after it is replaced. They will sit side-by-side if installed correctly. Turns out that the crunching/grinding noise was the chopper trying to chop up one of the clips that holds the silverware basket on the bottom rack. It was in many small pieces and had ripped up and split the impeller shaft.The dishwasher is back together and running perfectly. Thank you for very clear instructions on replacing the part and the quick delivery of the product.

At first I looked at the screen on the inlet to clean it out, but though dirty that wasn't it. I ran the dishwasher thru its cleaning cycle, adding water by hand whenever it was called for and it worked fine so I eliminated the master control as a problem. I then checked the overflow relay to make sure that it hadn't permanently opened by shorting it during a fill up cycle and that didn't work. I then ordered a new inlet valve cause that seemed like the most likely culprit. Simply disconnected the inlet pipe with a wrench and unscrewed the valve and put the new one in. Works like a top. Great dishwasher - Great site for ordering parts.

I had called an appliance repairman...I gave him the model #- he called me back in 2 seconds and said it was too old.. no parts available.. wanted to charge me $100 to come and look.I found parts select online. the part came in one day... and my handy man/put the new bracket on.. the dishwasher was put in new in 1991 and still works like a charm..thanks thanks

I popped all the new parts in place and all is well.

Removed bottom cover. Opened the door to take pressure off old springs. Removed the both old springs,with pliers. Replaced with the new springs. The new springs are not adequate for our heavy door.Our door has a wood, cabinet matching cover. The door falls down, if not held firmly. The springs are not as heavy duty as the old ones.

Used the diagram and disassembled and reassembled.Used most parts that were in kit as it also fit other models and did not need all the parts.

I looked in the bottom of the dishwasher after browsing the website regarding possible solutions. When I removed the bottom spray arm I noticed three screws missing from the pump housing. The loose pump outlet had allowed the seal to push out. Ordered-Normal shipping on the part.

The video was great! I couldn't have done it without it. The repair took me a little longer than expected because I did not have the right tools (torx head screwdriver), but once I went out and bought it, the rest was fairly easy. The old impeller had some build-up on it, so it was pretty hard taking it off the motor shaft: this was one of the hardest parts, since I was afraid of forcing it out and breaking something. Once I cleaned up the motor shaft, however, the new impeller went in easily. Both the old impeller and washer seal were damaged. Overall, I was very happy with Partselect's fast shipping, easy-to-use website and incredibly helpful installation videos. The machine is now not only NOT leaking anymore, but dishes are coming out MUCH cleaner. The dishwasher is over ten years old, so I was happy that this low-cost fix made such a big difference and we didn't have to buy a whole new dishwasher.

The dishwasher was making grinding noises and then stopped draining at all. I was able to follow the video directions and replace the parts from the drain and wash impeller kit, but it did not solve the problem. Must be the pump or something else. Was worth a try and partselect.com was good with service and price.

The repair was fairly simple and made easier with an installation video. The repair went well and there's no more leak.

Initially, I was going to call a repair-person to fix the dishwasher, but decided to check and see what was available on-line. I was very surprised to find a video on YouTube for my specific model. Even more surprising was the relative ease to perform the repairs, after watching the video. I have the proper tools, so I disassembled, per the video and found the problem. I was elated to see how easy it was to order the parts kit. It came in three days, and within 1/2 hour after parts arrival, I had the dishwasher purring like a kitten. What an excellent service. If you can turn a screwdriver, you can fix your appliance, via these well-done videos.