6651588582 Kenmore Dishwasher - Instructions

popped off the old rollers + tracks; then snapped on the new ones; as my granddaughter would say "easy peasy lemon squeezy". Took hardly any time at all. :-)

I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great

I looked in the bottom of the dishwasher after browsing the website regarding possible solutions. When I removed the bottom spray arm I noticed three screws missing from the pump housing. The loose pump outlet had allowed the seal to push out. Ordered-Normal shipping on the part.

I simply looked at the remaining spring to see which notch it needed to be attached to. I went in very well using a long needle nose plier. Works great.

I reviewed your video and followed the steps, I appreciate the video. I used the tools described in the video; it was a simple process. Thank you Parts Select. .

1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.

Used the diagram and disassembled and reassembled.Used most parts that were in kit as it also fit other models and did not need all the parts.

Unsnapped the old rollers and snapped in the new ones. Worked great and easy. I was very pleased that the parts came so soon as well. Thank You, Ms. Cason

Turned off water and power. Used small nut diver to remove two upper screws from kick-plate, and loosen two screws in lower key slot of kick- plate. Removed kick- plate. Used plier to compress snap ring and remove hose to washer. Pulled off electrical connector. Used 5/6 wrench to remove copper water inlet. Used nut driver to remove two screws holding old valve. Once out removed the water connecting elbow from the old valve and installed it on the new valve. Reversed process to reinstall. Didn't even have to remove washer from the counter. My 25 year old washer is working like new again.

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install

This Whirlpool model has the water inlet valve located in the front left of the dishwasher. It was not necessary to remove the dishwasher from under the cabinet. Disconnect the power at the breaker box and turn off the water supply to the dishwasher. Place a towel under the Valve as there will be a small amount of drainage from the water lines and the Valve when disconnected. After removing the front plate on the bottom, I could easily access the 2 screws securing the Water Inlet Valve. Disconnect the water lines on the Inlet Valve and the power connection. . Mount the new Water Inlet Valve, re-connect the water lines and the power connection to the Valve. Turn on water supply and check for leaks. Turn on power.

Watched "Steve" install the drain and wash impeller kit and then I did it.

I tried going online to get some diagnostic help and never found a site that had a step by step help plan. I then did a little reading on different sites, to eliminate and perhaps diagnose my problem I use epoxy to glue the impeller(which spun freely) to the screw and it held long enough for me to see how it worked. I surfed sites to find the least expensive drain and wash impeller kit. One site had a cheaper price but I chose Parts Select because of the shipping so the end result was the best results for me. I am not sure but the estimated time was 1.7 or 1.8 days delivery that I did not believe would happen. When I received the parts and did the repair my final time from ordering was less than a day and a half. I could not have done the job myself without the video because the parts were very different. My biggest obstacle, other than my ignorance, was some sort of chemical on the screw that would not allow me to loosen it. I used a dremel to cut the head off and then a torch to heat the stub so I could remove it. After I received the kit I saw a chemical on the screw threads so online research told me heat loosens the chemical. My dishwasher is around 25 years old,I have worked on it three times now and replacing the impeller was the most difficult task to date. Should it last and develop another problem I will go to parts select first and start my quest.

My dishwasher quit working the week before Thanksgiving, and to say the least, my wife was quite concerned. I did not know what was wrong, until I found the info on this website, including a how to repair video. I watched the repair video on the website when I ordered the parts. Other than my wash arm being different from what was shown in the video, it went exactly as shown in the video. I'm glad that the video, and the bag with the parts told me that there are fewer parts than originally were installed on the original. The parts looked like they had been redesigned a little, and were easier to assemble. Overall, I will be getting any repair parts I need for other appliance repairs in the future from here. Thank you for making this experience as easy as it was.

I watched the video then followed the procedure accessing the impeller/grinder from inside the tub. Had I not watched it, I would have torn into it from the bottom by removing the motor, etc. with disastrous results. I was quite depressed when installation of the impeller kit did not resolve the problem. I remembered from the survey that 56% of problems were solved with this kit; BUT, another 24% found that the check valve on the discharge line was the problem. So I removed it and lo and behold, it was partially plugged with broken pieces from the old impeller. The 1 page sheet that comes with the kit is simply a diagram of the parts included, there are no instructions ---- watch the video!!! All said and done, my experience with PartSelect was first class. They are 5 Stars in every category and I would highly recommend them.