6651560591 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from Palm Springs, CA
- Parts Used:
- WP300845
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Part
I just installed the new part. There were no tools required. I bought an extra part
I ordered the part on Monday, and it arrivefor the other side in case it breaks.
d by FedEx the next day. I live in Southern California.
Great service, thanks.
I ordered the part on Monday, and it arrivefor the other side in case it breaks.
d by FedEx the next day. I live in Southern California.
Great service, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from Coos Bay, OR
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
We needed a new bottom dishrack the old one was very rusty
I ordered a new rack, snapped the stuff together, and slid the old one out and the new one in. Fit beautifully. Piece of cake and much cheaper than a new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eieen from Methuen, MA
- Parts Used:
- 675611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end loop on each end of spring broke off
Looked at right side of dishwasher to see how it was attached and did the same. Spring was slightly shorter than the original and the loops are not a sturdy. Will see how long it last.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Jupiter, FL
- Parts Used:
- 675544
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Drain hose cracked. Leaked and warped wood floor.
Checked fill line. No leak. Checked drain hose, found crack in hose. Ordered the part, replaced.
Removed hose clamps on drain to DM and garbage disposal. Replaced hose and tightened clamps. Checked for leaks. Buttoned up faceplate on bottom of DM.
Removed hose clamps on drain to DM and garbage disposal. Replaced hose and tightened clamps. Checked for leaks. Buttoned up faceplate on bottom of DM.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip D from Auburn, AL
- Parts Used:
- 4387043
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch had broken on detergent dispenser cover
Remove retainer that holds door color slide in front of door & then remove the slide. Remove cardboard backing, remove electric latch release, remove latch & replace with new one. Open door & slide out the cup dispenser cover pin & spring & replace with new ones. This was all straight-forward & simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Greene, ME
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Installed wheel assemblies to rack
Assemblies snap on, no tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Las Vegas, NY
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
soap door hinge broke
I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicole from Newnan, GA
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The previous rod holding the cup in place broke
Remove completely the old one and installed the new entire kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- craig from Columbia, TN
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
was just missing the door and spring
You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Millbrae, CA
- Parts Used:
- WP302711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water leaking from the right front of appliance
The repair was simplicity itself. Remover the sprayer arm, removed the torx screws, replaced the seal, and reversed the process of disassembly. When I found out where the dishwasher was leaking from, I called KitchedAid and was ready to replace the overflow float. The part was 42.00 and wouldn't have fixed the problem. When I found this web site and read other peoples experience, I checked the pump seal, and it was obvious that it had blown out. That saved me a Loy of time and money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delano from Durham, NC
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
spring on dispenser broken
Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Albuquerque, NM
- Parts Used:
- 3367910
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Gasket around nozzle cap wouldn't stay on - in two pcs.
As there was not a replacement gasket listed in the parts lists or schematics, I ordered the entire nozzle cap hoping the gasket would come with it. It didn't so I glued the gasket in place and installed the new cap. I also replaced the washer arm bearing while I had the cap off. I am hoping the nozzle stays in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruby from Saint Marys, GA
- Parts Used:
- 675238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
missing part
screw it in then hook up the hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Taylor, TX
- Parts Used:
- W11086533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Unfortunately, a mouse had made its home on top of our surround insulation. For hygienic reasons, I replaced the surround.
1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fernando from El Paso, TX
- Parts Used:
- 675806
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher making a noise (lower area)
I reviewed your video and followed the steps, I appreciate the video. I used the tools described in the video; it was a simple process. Thank you Parts Select. .
Was this instruction helpful to you?
Thank you for voting!