Models
>
6651560591
6651560591 Kenmore Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$109.17
This dishwasher drain and wash impeller kit comes with both the drain and wash impeller, gaskets, chopper and installation screw. This part helps stop your dishwasher from leaking and helps with the ...
In Stock
In Stock
In Stock
$5.42
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
$8.04
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
In Stock
This kit includes spring, retainer and protective tip. It is recommended to replace both springs at the same time.
In Stock
$7.95
This is a multi-use cover screw. It fits appliances such as dryers, ranges, washers, dishwashers, refrigerators, air conditioners, washer dryer combos, freezers, wall ovens, microwaves, dehumidifiers,...
In Stock
In Stock
This kit also includes the lid hinge pin, spring, snap and latch.
In Stock
In Stock
$277.64
This kit comes with the wheels, bumpers, fold down tine and flexrow retainer.
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 6651560591
Viewing 10 of 10Leaking
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Not cleaning dishes properly
Fixed by these parts
How to fix it
Will not dispense detergent
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Not drying dishes properly
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
leaking from tub above motor
Disconnect unit and remove from under counter. remove lower spray arm, tip over dishwasher on it's back, diconnect wires from motor , unscrew drain fitting rotate motor mounts to and lift pump and motor assembly up and out from inside the dishwasher. thoughly clean all parts during pump disassembly( under running water and a toothbrush
... Read more
works well) . Looking at a parts diagram,and using your memory from disassembly replace the new seals and put it all back together, with patience you can do anything and use common sense.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from Portsmouth, NH
- Parts Used:
- 675238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher Not Draining
Ordered both drain & wash impeller kit and the drain check valve with o-ring. Decided to test the cheaper drain check valve first. Pulled dishwasher out from wall & adjacent cabinetry; removed drain hose from disposer and drained as much water as possible; "jacked" side of dishwasher to gain access to drain hose and drain check valve; us
... Read more
ed pliers to remove hose clamp; placed flat pan underneath to catch remaining water drainage; unscrewed drain check valve; tested under bathroom faucet--determined faulty; replaced with the new one, restored connections, reset dishwasher in proper location; voila--fixed! Plan to return the unneeded impeller kit.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Dousman, WI
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench (Adjustable), Wrench set
Grinding Noise
Grinding Noise when running. I was not sure of problem and thought that a new Dishwasher may be needed if motor was the problem. After taking the bottom rack and spray arms out I came across my first problem. I believe it was the impeller design that has a 1in hex nut with a bolt in middle that needed to be removed. I needed a 90 degree 1
... Read more
in wrench to hold impleller while I removed Bolt. Luckly I have a friend that is a mechinist who made me a wrench.
After that the grinding cause was discovered - Broken glass that grinded the cermic shaft that is over motor shaft. I did not small drops of water under motor during grinding due to damaged cermic shaft.
$24 and 2 days later my dishwasher is as good as new. Sugguest you sell a 1in 90 degree hard plastic wrench for holding impeller which bolt is removed.
Thanks
PS. - Best part of your site is Parts detail which was very helpful for me to understand assembly.
After that the grinding cause was discovered - Broken glass that grinded the cermic shaft that is over motor shaft. I did not small drops of water under motor during grinding due to damaged cermic shaft.
$24 and 2 days later my dishwasher is as good as new. Sugguest you sell a 1in 90 degree hard plastic wrench for holding impeller which bolt is removed.
Thanks
PS. - Best part of your site is Parts detail which was very helpful for me to understand assembly.
Read less
Was this instruction helpful to you?
Thank you for voting!