6651574991 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dale from Kingston, MO
- Parts Used:
- 3374621
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water would not come in when the dishwasher was turned on
Just removed the old one and installed the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from SELKIRK, NY
- Parts Used:
- 4318273
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad door switch
i took the inside door off and took the 2 switches out and replaced them; not too difficult.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Bellerose Manor, NY
- Parts Used:
- WP661566
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
High limit thermosat blowes when on santi. rinse
Remove blown high limit therm.and replace with the new high limit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Woodward, IA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dishwasher leaking in lower front door area
Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Columbia, MD
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Soap cup latch was broken and dispenser cover was worn.
Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- perry from cynthiana, KY
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
detergent dispencer door spring and pin worn
I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Fort Oaks, NC
- Parts Used:
- WP661566
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Machine would shut down during the wash cycle.
I read information on this website about the function of the high limit thermostat. I found that it was the problem by disconnecting the two wires on the thermostat and straight wiring to bypass it. This allowed the machine to work properly so I ordered the high limit thermostat. To replace the part I used a screwdriver to remove the instrument panel and replaced the high limit thermostat by disconnecting the two wires from the old thermostat and connecting the wires to the new thermostat. I then replaced the instrument panel. My machine is working properly again..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- matt from grant park, IL
- Parts Used:
- 676413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dish washer soap drawer would not work
we followed your instructions submitted via e-mail and they worked out just fine....thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from CHESTERFIELD, MO
- Parts Used:
- WP3369193
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The plastic strip on the access panel that attaches by two screws to the washer body had broken off.
The broken access panel was VERY TIGHTLY engaged to the metal vent. After much tugging and pulling, trying to get the vent free of the broken access panel the two apart (without success) I used a large flathead screwdriver to split the portion of the access panel (its plastic) that held to the metal vent. Once the vent was free of the old panel, it could be easily snapped together to the new panel and this new assembly was held in place with two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rahul from Irvine, CA
- Parts Used:
- WP3369193
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The plastic brackets that hold the screw against the frame had broken
Remove the Access Panel retainer from top of the panel. Then remove the Access Panel and the Spacer Panel from the front. Then remove the Extension from the bottom. This step was kind of difficult, I ended up bending the plastic bracket on the pane since I was going to throw it away anyway. Install all the parts onto the new panel in the reverse order. Screw the panel back on to the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrel from rosamond, CA
- Parts Used:
- WP8066018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lid Spring
Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Little Rock, AR
- Parts Used:
- 676413
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Top of the Soap Cap Latch was broken
The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. Thanks for the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Rehoboth, MA
- Parts Used:
- 676413
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch worn out
Followed vidio instructionson web site. Quick easy fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Charlotte, MI
- Parts Used:
- 4318050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Broken door spring
The repair was very simple. Simply pull the dishwasher out far enough to access the springs, remove the old with pliers and install the new springs in the same spot as the old ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Amboy, WA
- Parts Used:
- WP3369193
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Plastic edge broke off
Lower panel was easy to replace. Had to apart the trim on the old one and glue. No problems at all. Glad to be able to gets the part to fix. One of the plastic edges that holds the screw broke.
Was this instruction helpful to you?
Thank you for voting!