6651574991 Kenmore Dishwasher - Instructions

Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!

I read information on this website about the function of the high limit thermostat. I found that it was the problem by disconnecting the two wires on the thermostat and straight wiring to bypass it. This allowed the machine to work properly so I ordered the high limit thermostat. To replace the part I used a screwdriver to remove the instrument panel and replaced the high limit thermostat by disconnecting the two wires from the old thermostat and connecting the wires to the new thermostat. I then replaced the instrument panel. My machine is working properly again..

The repair was very simple. Simply pull the dishwasher out far enough to access the springs, remove the old with pliers and install the new springs in the same spot as the old ones.

Lower panel was easy to replace. Had to apart the trim on the old one and glue. No problems at all. Glad to be able to gets the part to fix. One of the plastic edges that holds the screw broke.

Bought a house and with it can an old whirlpool dishwasher in where the soap dispenser lid would latch, as the latch itself was gone. Ordered the latch from part select and used the installation video to switch the latch out. Only problem I came across was that the torx screws at top of he door were free spinning. Ended up using a flat head for leverage to finally get the screws out. Everything works perfectly for once.

I replaced the seal, still leaked. Once I noticed that it was only leaking from the left side, we did a Google search to find that the screen in the upper left of the door could be the issue, causing back pressure. Once the screen was cleaned, no more leaks.

My soap dispenser latch was coated in grit, the gasket was deteriorated, and the spring was barely strong enough to open the door, so the door didn't always latch closed or open when it should. I followed the video and everything went exactly as shown. Once the liner was removed, I discovered the back (including the latch mechanism) was covered in soap residue and other gunk. I hosed it off on the backyard and resumed the repair. The dispenser now latches easily and opens with a convincing SNAP. I wouldn't have known how to replace the latch without the video. Great website!

Put the new part on

Turned off power to dishwasher. Removed inner door panel. Cut wires as directed and installed new switches. Also installed new spring on soap door opener. Reassembled, ran and tested. Take your time, this repair is pretty simple.

removed the 2 water deflector and slipped the new ones in , in place.. very easy to do but it didn't seem to stop the leak so ordered the door gasket

Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes

Just removed the old one and installed the new one

i took the inside door off and took the 2 switches out and replaced them; not too difficult.

I paid a repairman over $100 to tell me he could find nothing wrong with my leaking dishwasher (it didn't leak when he ran it). I narrowed down the problem to a missing water deflector, but decided to replace the door gasket as well. It took less than 5 minutes to do the job. The only tool I used was a pair of needle-nose pliers to grasp the old door gasket and get it coming out of the groove. Thanks PARTSELECT for super-fast shipping and a website that is easy to navigate. I'll be coming back, 'cause all of my appliances are getting some age on them!

I used a screwdriver as a wedge to remove the existing panel and inserted the new black panel into the groves located on the front of the dishwasher. Installation was easy because I followed the instructions from the website. Piece of cake. Less than 2 mins.