6651597999 Kenmore Dishwasher - Instructions

The repair was simple except for removing the thread portion of the old retainer nut from the lower housing. I had to remove the lower housing and separate the male threads of the old plastic nut from the female threads in the lower housing. That took 25 minutes since I did not want to ruin the female threads. Once removed, the new parts went into place easily.

The part arrived much sooner than i was ready for. with a square allen wrench I was able to install the tube in no time.

Removed the lower spray arm assembly thumb screw and lifted off the spray arm assembly. The lower seal had disintigrated - couldn't even find any pieces in the filter. After reassembly with the new seal and bearing I turned the spray arm by hand to ensure it was not binding. There was still was, what I would consider, some excessive wobble. I fashioned a shim washer out of some plastic from a Folgers coffee can lid and installed it on the thumbscrew threaded shaft and tightened it all down finger tight - it works very well and now, and no wobble.
I relaced the upper spray arm seal while I was doing the job (both the upper and lower seals are the same part #). I figured it would go out on me eventually, so I might as well replace it while I was doing the lower arm work. Kept the old upper arm seal as an emergency replacement.

Cleaned the filter screen of all debris (it is amazing what collects there over time). Cleaned the stainless tub with some spray Greased Lightning, ran the rinse cycle, and then put a few tablespoons of citric acid crystals in the soap dispenser and ran the dishwasher on NORMAL WASH with temperature boost.
Looks new inside; cleans the dishes, glasses and utensils well (no water spotting); and is nice and quite (like when it was new).

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

First I removed the plastic bolt that holds the wash arm in place This exposed the upper ring that was worn out . I then lifted the arm off which exposed the larger ring. I replaced that ring, and then I put the arm back on and replaced the upper ring. I put the plastic bolt back in place and the repair was complete.-- Really Easy plus the dishwasher gets the dishes clean now

Just removed old seal and put the new on in place no problem

Partselect provided me with tracking information for my order, they also provided an installation video. So when I replaced the door seal it was a few minutes to remove the old seal and about five minutes to put in the new one and it was all done.Thanks to Parts select it was a piece a cake

I read a couple of stories about how easy these are to break when installing. So I used extra care, and made sure to push carefully in just the right places.

What worked for me was raising the tines of the cup rack to apply some leverage as I squeezed the clips into place with my fingers. No tools. No broken clips. No injuries. No cursing.

Removed the screw that held the mount in place. Snapped the new mount place (no screws required).

Fast & easy.

I removed the bottom spray arm and replaced the worn part. Now the arm turned freely and was performing as it was designed to do. I appreciate parts select for having the part available since the manufacturer no longer supported the model.

You'll have to excuse me, but I'm a women and don't know the exact names for the parts.
Since my nut broke off in two parts, I had to remove the screws on top of the drain screen to get the other half. I just used a philips screwdriver and removed the 7 screws. Took out the broken part, and that was it. Put back the screws, put on the spinning water arm and put in my new part to keep it in place. Thank you. This saved alot of money for a repair person.

replaced door seal,lower door seal and wash arm bearing ring-now it leaked when it was running.put old door seal back in and no leaks. all it needed was the wash arm bearing, also I cleaned out the inside of the water level float,which lowered the water level in the bottom of the dishwasher.

Replaced dispenser. Leaked around dispenser the first time i installed. Re-tightened mounting screws and everything worked OK.

Removed the plugs in the slides, removed the rack, slid the new rack in and replaced the plugs.

Great fit. take out old one and drop in new one. Piece of Cake.