JDB6510AWK Jenn-Air Dishwasher - Instructions

After repairing this dishwasher 5 times during the past 8 years this one was real easy: Open door, unscrew inside cover and carefully move over to one side. Unplug soap dispenser, unscrew soap dispenser and remove. Fit new dispenser, reconnect it, put inner cover back in its place and secure it with the retained screws and you are back in operation. Hans.

First, I removed the foot plate(s) at the bottom of the Dishwasher. (2 screws each side)

Then I removed the two top screws at the front of the dish-washer. The screws were mounted into a board under the counter that had broken loose. (A minor secondary issue specific to my situation.)

I gently inched the dishwasher out from under the cabinets.

SLOWLY, I tipped the dishwasher over on its side, allowing the water still inside to drain into a pan. Minor cleanup required for the cup or two that missed.

I then had access to the part. I disconnected the power from the wall socket, and I closed the valve for the inlet water from under the sink.

I removed the screws holding the Water Valve to the DishWasher case. Then I took a sharpie and marked one side of one of the two power connectors, black-mark to black-mark.

When I went to disconnect the inlet pipe, there was more dripping than I expected, so the valve under the sink was not closing completely. I needed to shut off the water supply to the house for the next stage.

I disconnected the inlet water supply, which continued to drip slightly into a bucket. I then removed the coupler from the old water valve. It was badly clogged and corroded, so I went to a local HW store and found an exact match 3/8" to 3/8" right angle coupler with compression fitting on one end.

BIG TRICK, before installing the new coupler, WRAP the compression fitting threads with teflon tape. You will not be able to wrap it once it is installed. In fact, I needed to uninstall the part once after I discovered this, to wrap the threads smoothly.

Once pre-wrapped, wrap the other threads that screw into the water valve. Tighten until secure, AND aligned with the direction of the flow tubes of the original.

Match the electrical connectors, black-mark to the same position as before. (The new water valve will NOT have the black-mark on it, unless you transfer one!)

Connect the Water valve back to the Dish Washer chassis with the two screws previously removed.

Connect the inlet water back to the compression fitting with the pre-wrapped threads.

Gently return the dishwasher to upright, and then plug it in.

Open the valve under the sink slowly and watch for drips or leaks.

Run the dishwasher at the start of a cycle, long enough to determine that the valve activates, and allows water to flow. Then stop the cycle.

Gently walk the dishwasher back under the counter, observing that you do not kink the copper water inlet pipe, or the drain pipe.

Adjust the feet, if necessary, back to fully support and level the dishwasher.

Install the two screws holding the dishwasher to the cabinet front. Then install the kick plates and tighten those 4 screws.

Clean up any residual water from the process.

Removed rear of front door to access back panel to access two handle screws and replace handle--very easy.

Pulled the dishwasher out. Determined that it was leaking from the air/water inlet. Ordered the seal and replaced the seal by turning the inside cover counter clockwise while holding the outer water inlet. Replaced seal and installed water hose. Put dishwasher back inside cabinet and leveled. If you don't try to fix it yourself, It could cost more then what it is worth.

I surfed the net using phrases like "dishes not clean" and found a series of possible solutions. When I noticed that the water in the washer was cold, I realized it was a heating element issue. Using a multi-meter set to the lowest resistance I tested both ends of the heating element (OF COURSE I SHUT OFF ELECTRICITY TO THE DISHWASHER FIRST!!!) and found it read a steady 16 ohms. Then I followed the orange leads to the limiter, removed the leads and tested resistance and found it at near zero. Touchdown.

I ordered the new limiter, had it in a couple of days and installed in in 5 minutes. The hardest part was putting the metal cover back on the bottom of the unit.t

We were happy to find the basket we needed listed on your website, even after we could not find it on the Maytag site. It was perfect. I can't believe we lasted almost 2 years with the broken basket we had.

The bottom rack was easiest, just picked it up out of the dishwasher and moved the sprayer and the silverware holder from the old rack to the new rack and set it back in the dishwasher. The top rack was a little tricky, it took a minute to figure out to remove the little end-caps on the runners and then it just slid out. Slid the new one in, replaced the caps and moved the upper rack basket. It took less than 15 minutes to fix and now it's like a brand new dishwasher!

Our first effort was to replace the lower washer arm that had splits in the sides of this plastic part. While this increased the water pressure in the wash cycle some it was not enough to adequately wash the dishes. We read that someone else had to clean out the filter which was below the lower washer arm assembly. Thus, we took off the loweer arm assembly by screwing off the hold down assembly in the middle of the arm. We then took off the pump cover by removing the 6 screws that hold it in place with a #3 metric allen wrench. When we took of the cover we could see that the pump filter was so covered with deposits that it was not letting the water through to the pump. Rather than spend hours trying to clean the filter and pump cover we decided it was easier to repalce them. Thus, we ordered the parts and replaced them. The dishwaster is now working fine. We appreciated the information that others had shared that helped us find and fix the problem.

The dishwasher is well engineered to perform this work.

Remove the bottom two panels to provide access and visibility to base of pump motor.

Locate plastic pump locking lever and push toward rear of DW to unlock pump from DW.

Inside the DW remove basketsand spray arms. Revove screws holding cover over pump motor and remove cover.

From below raise pump motor and support with block (piece of 2x4 worked well).

insde DW, removre old gasket, clean well around pump and botom of DW, install new gasket.

From below remove block to drop pump motro back into place, and re-tighten locking lever by pull toward you.

re-assemble inside componets, run through a rinse cycle to test for leaks and replace bottom panels.




I

It is an easy repair, but you need the right tools to remove the inside of the dishwasher door (a hex wrench set) and then to remove and replace two screws holding the plastic door handle in place (1/4 inch Allen wrench). Make sure the power is off even for this repair because it can't be done without coming close to electrical elements.

I was able to remove the old handle and place it on the new basket - using only a screw driver.

I removed the plastic retainer that held the lower spray arm in place. After removing the lower spray arm I was able to remove the 6 hex screws that held the cover over the filter screen and the discharge housing assembly. I was then able to remove the bolts that held the upper part of the discharge housing assembly, and replaced it with the new part that I received. The rest of the job was simply putting it back together.

Note: While repairing the broken part, I noticed a small leak under the machine around the float assembly. This was simple to fix. Remove the small lock ring on the bottom of the float. Pull the float out and clean the grease and soap scum out of it. Put it back in and attach the lock ring. No more leak and the water gets turned off when the float activates the switch. Something that everyone should check periodically.

Read the experiences here, very helpful. Bottom slides out first - really easy. The new part comes with rollers, you don't need to remove the old ones. Now the only problem, getting the sprayer off the bottom basket. Look carefullty, you must use a screwdriver to release one side of the sprayer, then it works off easily. Make sure you note the orientation of the base of the sprayer. Reverse steps above and you are done. New tray slides in. Our new tray was a bit wider than the old one so we needed to use a bit of pressure to "shrink" the back just a wee bit.

The upper is easy also. Since the rails are uneven, make sure you put the high rollers on the high side no matter what your wife told about how it is supposed to go in. The end caps snap inward and slide out of the rails. Easy once you know. The uneven rails are obvious once you notice. Total time was 45 minuts, 30 of which was figuring out how to get the sprayer off without damage.

Would be nice to know the factory recommendation for removing the sprayer.

I took the bottom cover off and pulled off 2 wires and removed 2 plastic nuts. I removed the old part and removed the O rings from the old part and installed the new heating element. Replaced the plastic nuts and the two wires. It was very simple. The hardest part was lying on my back to get to the wires and nuts.

The replacement of the spring linkage was simple - the pulling out and pushing in of the under-the-counter dishwasher was the difficult and time-consuming part. The repair of the part took less than a minute.

The actual repair -
1. Hook the linkage to the dishwasher door
2. Hook the spring to the dishwasher base
3. Hook the spring to the linkage.

Getting the dishwasher out to be able to make the repair involved:
1. Unscrewing the base panel (6 screws had to be removed)
2. Unscrewing the dishwasher from the counter (two screws)
3. Turning off the water supply
4. Disconnecting the inline water supply from the dishwasher.

Once the part was replaced, I had to return the dishwasher to its original position, which meant performing the four steps (in reverse) used to pull out the dishwasher.