JDB6510AWK Jenn-Air Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from MARSHFIELD, MA
- Parts Used:
- W10139223
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Needed to replace original dish rack which was severely rusted
Dish rack not same as original. No raised section on right for drop down ledge. Also the old rack had a section for wide rim bowls. New one is for plates only. Otherwise it is OK
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from CARLINVILLE, IL
- Parts Used:
- W10139223
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lower rack was losing all the little spokes. They were breaking off and rust developed.
We twisted the tower counter clockwise to remove from the old rack. It was a bit tight but came off quickly. Then inserting the tower into the new rack went very smoothly. That's all there was to it. The new rack did not have a place where I could attach the flip down shelf, but I rarely used it anyway. Love partselect. They helped me avoid buying a new dishwasher. Using Cascade pods, my dishwasher cleans like it is new and it is 25 years old!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Cornish, ME
- Parts Used:
- WP99001359
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
water not flowing into dishwasher
turn off breaker
turn off water supply line
note wire color locations on notepad
disconnect 2 spade lugs (pliers)
disconnect inlet line (adj. wrench)
disconnect outlet line (pliers on hose clamp)
remove old valve assembly (4 screws w/nutdriver)
remove ground jumper from old valve
remove inlet pipe ell from old unit (vise & pliers)
clean open end of pipe ell (file)
apply teflon dope tape to pipe threads
install pipe ell on new valve
reorient solenoid 90degrees cw to match Maytag installation
reinstall ground jumper
install new valve assembly in dishwasher
reconnect hose and hose clamp
reconnect inlet line
reconnect spade lugs
turn on supply line, check for leaks
turn on breaker
start washer at appropriate cycle to test water flow
done!
turn off water supply line
note wire color locations on notepad
disconnect 2 spade lugs (pliers)
disconnect inlet line (adj. wrench)
disconnect outlet line (pliers on hose clamp)
remove old valve assembly (4 screws w/nutdriver)
remove ground jumper from old valve
remove inlet pipe ell from old unit (vise & pliers)
clean open end of pipe ell (file)
apply teflon dope tape to pipe threads
install pipe ell on new valve
reorient solenoid 90degrees cw to match Maytag installation
reinstall ground jumper
install new valve assembly in dishwasher
reconnect hose and hose clamp
reconnect inlet line
reconnect spade lugs
turn on supply line, check for leaks
turn on breaker
start washer at appropriate cycle to test water flow
done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from baldwin, NY
- Parts Used:
- WP99002839
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
cracked handle
Kids blame mom, mom blames cleaning lady. I blame cheap plastic part. ez install. Make your job ez wait for a helper to come home. When you undue 10 screws, second person can hold inner panel and door apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Marshville, NC
- Parts Used:
- WP99002187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Wash cycle would stop and hum like it tried to start.
Repair was simple. Diagnosis was wrong. Switch did not fix problem. Most likely a control electronic assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Brookdale, CA
- Parts Used:
- WP99001359
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
No Water caused soap to not dispense & no clean dishes.
I took off the front bottom panel for an easy access. The valve is located on the left. Shut off water to the dishwasher. Remove the bracket that holds the valve. Remove hoses and 2 wires on the valve switch. Install new valve by revesing the steps above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from Middletown, MD
- Parts Used:
- WP99001359
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Dishwasher not getting dishes clean
Piece of cake. I panicked for a minute before I realized that there was a threaded brass 90 in the inlet valve. It looked like it was the wrong part for a minute. Once I got the 90 reinstalled in the new valve, I had it back together in 10 minutes. It seems to be working better.
Was this instruction helpful to you?
Thank you for voting!
Door spring broke letting door fall down
This was really easy. I just took out the two screws securing the unit to the counter top and slid it out about 6 inches. Broken plastic spring linkage was obvious and easily accessible. I didn't know there was one on each side, I would probably have went ahead and ordered both and replaced them at the same time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- karen from forest lake, MN
- Parts Used:
- WP99002839
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
plastic handle cracked and broken
took old handle off (loosened two screws to do this) and replaced same way.......took two people only because one held the door separated while the other replaced the handle........
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from Rockaway, NJ
- Parts Used:
- WP99003317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
rinse dispenser was clogged and unusable.
I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.
The new part arrived quickly and was the perfect match.
The new part arrived quickly and was the perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from henderson, NV
- Parts Used:
- WP99003317
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
detergent dispenser door latch not holding
from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Bensalem, PA
- Parts Used:
- 99001995
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
dishes werew not drying anymore
follow the instruction on the web site that you listed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Bloomington, MN
- Parts Used:
- WP902461
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
would not wash or pump water out. Made noise like a bearing was out on motor. Went to dealer and was told that the motor and pump assy was not available because the washer was too old (18 years) and if a part was found it would cost $205. He wanted to sell me a new washer for $215. I went home
Removed the 6 screws holding the pump and motor assy. Disconnected the two hoses and wiring connector. Removed the motor and pump, removed the pump parts to get down to the impeller. Removed the old impeller (one screw) and installed the new impeller. Put every thing back together and it worked fine. Every one is happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John M from Norwalk, CT
- Parts Used:
- WP912653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Remove and Replace Door Spring Linkage
1) Emptied Dishwasher (roll-around model)
2) Tipped it onto its back
3) Removed Toe Kick (2 screws) and Bottom Cover (4 screws) (screw driver)
4) Opened Door to access side panel (careful not to let it drop on my fingers)
5) Using Torx driver, removed two screws holding side panel on. This makes it easier to access the linkage and spring.
6) Removed broken link
7) Installed new link and spring noting the spring direction from the spring on the other side of the door.
8) Pulled spring over the bottom rail bracket with pliers.
9) Reinstalled panels in the reverse order.
2) Tipped it onto its back
3) Removed Toe Kick (2 screws) and Bottom Cover (4 screws) (screw driver)
4) Opened Door to access side panel (careful not to let it drop on my fingers)
5) Using Torx driver, removed two screws holding side panel on. This makes it easier to access the linkage and spring.
6) Removed broken link
7) Installed new link and spring noting the spring direction from the spring on the other side of the door.
8) Pulled spring over the bottom rail bracket with pliers.
9) Reinstalled panels in the reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from San Angelo, TX
- Parts Used:
- W10139223
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower rack rusted and falling apart
I pulled out the old rack, removed the spraying apparatus, attached it to the new rack and slid it into place.
Was this instruction helpful to you?
Thank you for voting!