JDB1090AWS Jenn-Air Dishwasher - Instructions

from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.

Switch was not the same switch as what was in the unit, similar but switch was normally closed instead of open, so had to take the switch apart and change sides with the contacts! should be the same, but was not, so in the end worked fine after an adjustment!

I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.

I used a flat screwdriver and small forceps pliers to remove the broken wheel on the lower rack, followed the online video and it was done in a few moments. On the upper one I removed the end piece using small forceps pliers then removed the broken wheel. I used the flat screwdriver to ease the new wheel assembly on the the rack, engaged it in the track then replaced the end piece on the track and the repair was complete. I did order 2 of each item to keep as spare for the next repair!

with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.

Impeller bolts to plastic chopper mount which is screwed to the top of the motor. Threads on chopper mount were stripped causing impeller to not spin fast enough (replacement mount, which is part of the chopper kit, is metal). Installtion was not difficult.
You have to reach underneath the washer and wedge a screwdriver on top of the motor to hold the shaft from moving.

Snapped the old part out and snapped the new part in.
It was a piece of cake.

It is such an easy snap-on repair that a child could do it. I am grateful that your company had a picture so I could compare my broken part with the ones you guys have as I couldn't find my model number. I took my time to do the job right, so it took me almost 15 seconds! lol

I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.

My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and replaced the screws. The whole job took about 20 minutes. It was a very easy job.

received new basket without a basket handle; had to remove handle from old basket & attach it to new basket; took 2 separate tries to remove old handle & each try took about an hour; used screwdriver & pliers but had to be careful not to break handle; eventually used dimes to pry open & hold the attached sections of the handle open in order to free the handle from the old basket; we sure hope the new basket lasts a lot longer than the 2 years that the old basket lasted before it broke.

Troubleshooting: Noted soap dispenser full of apparently wetted soap, drying cycle dried to brick-like mess. Dishes full of soap particles, not clean. Water through floor and basement ceiling.

Pulled all racks (note arrows on ends of rack supports), used vice grips to remove bottom spray arm (better to use washcloth around little knob to protect from vice grips), unscrewed all torx fasteners to get assembly out. Had to carefully maneuver pump housing out since it attached to water distribution assy. Found stripped sleeve, but didn't understand function until I saw similar post on this site (Thanks!). Ordered seal and chopper kit, paid extra for "2 day" delivery and rx the next week due to holiday weekend (what's up with that? I ordered a linksys security camera on saturday and rx on Sunday from "Lasership"). Followed included instructions - worked fine. Note assembly order of pump with respect to water distribution assembly - I assembled and dissassembled twice due to forgetting interference.

Ordered part. (Part was larger than the original . That is it dis not fir int supports tha same as rhe original. Hut i modifird the support by assin copper wire to fanten the heater to the supports.) The instalation was no pronlem with a little engineering. Works like a charm, Wife Happy Most important result.
Elmer