JDB1090AWS Jenn-Air Dishwasher - Instructions

Docking station just pops out, you grab the right side and pop it off. Replace by placing the left side in place and then push the right side until it snaps in place. VERY easy.

The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.

The old docking station seals were getting very soft. To put a band aid on the wound until the new docking station got here I put a sleve on the washer bar feeder tube. This made an improvement. The docking station was removed using a screw driver to unsnap the station. Then all I had to do was snap the new one in. Be care ful not to pull on the piece the docking station is snapped on to. There are metal clips behind there that hold that water delivery tube on to the back of the dishwasher. Those clips are twisted on and can be striped off easily by pulling strait towards you. If that happens you must secure the clips using self tapping screws and a water proof sealent.

Pull dishwasher about 1/2 out of cabinet. Remembered to turn off power just in time. Removed electrical leads. Hand removed nuts retaining the heating element. Installed new element - hand tightened nuts.

1. Shut off water supply

- Remove water line and drain hose if you need to. I was able to simply move the dishwasher forward some to do this repair without disconnecting

2. Remove access panels on the bottom.
3. Open the door
4. Remove Door Gasket carefully (do not stretch)
5. Use torque 20 driver to remove 6 screws that were under the gasket

- Some of the screws were rusted for me so I had to use kroil, a pick to clean out rust, and a hammer to help get the torque driver in enough to remove the screws. A local hardware store had replacements.

6. Use Phillips screwdriver to remove screws holding mounting brackets
7. Carefully move dishwasher out some (Careful if you have a copper water hose you may want to disconnect it)
8. Remove the strike if it is attached above the metal bar
9. Lift the metal bar and push down on the tub to make room to remove the old mounting brackets (slide them up, forward, and to the side)
10. Put new mounting brackets in place (put mounting bracket under bar, slide over into place)
11. Reverse the order at this point.

Be careful not to stretch the gasket. I soaked mine in vinegar for a bit and gently washed with dish soap to remove deposits.

Dishwasher is in our summer cabin in Colorado so everything has to be drained for the winter. Not really sure whether this leak was freeze caused or that the valve was just old. Couldn't find a crack when I got the old one apart; might have been just an O ring needed. Anyway, just follow the video provided by this site for replacement of the valve; really easy. Biggest hassle for us was getting the dishwasher out (and back in) as it was wrapped in insulation which made the fit really tight. Thought I had everything I needed when I started but didn't have teflon tape which is needed for the brass fitting connecting the water supply to the valve (fitting is in your old valve and will be reused with the new one).

The "repair" was actually a replacement. My wife did it. She took out the old, damaged basket and dropped in the new, replacement basket. She removed the slotted lids because she doesn't think they are necessary and she doesn't like them. I got the old basket for holding small items in my workshop. The lids will be thrown away, unless I can come up with a use for them.

Open the door and remove old basket. Place the new basket in its plave. Time elapse approximately 20 seconds

Very simple. Just replaced the old one with the new one. Voila!!!

Just replaced with new basket. Fit like a charm!

I pulled out the dishwasher enough to tip it back and put a block of wood underneath the front leveling foot.
This step gave me more room to work on the valve.
I removed the lower cover plates to expose the valve.
I disconnected the incoming water line and unplugged the electrical connection.
I then unscrewed the bracket to release the valve from the case and took off the rubber hose attached to it.
I installed the rubber hose on the new unit and installed the bracket back in place. I then wrapped some Teflon tape on the threads of the valve fitting and re-installed the water supply line. I re-installed the electrical connection.
I then turned on the water to check for leaks. Once I was certain there were no leaks, I re-installed the lower cover plates and took out the wood block and pushed the dishwasher back into place and re-installed the screws that held it in place.
I then ran a load of dishes to make sure everything was working properly.

Removed all the screws holding the inside panel of the door to the door itself. Lifted out the old broken door latch. Pulled the wire clips from the 2 switches located on either side if the door Latch assembly. This is a bit difficult. You have to keep working the wire clips back & forth; Up & down until the clips are free from the switch metal contacts. Reinstall the wire clips on the new door Latch assembly making sure you attach the black wires and white wires on the same side of the new latch assembly as on the one removed. Replace the new latch assembly aligning the mounting holes on the door with the new latch holes. Replace the inside panel aligning the holes and replace the screws. The screws were the star head type so you need a special driver bit. I used the box the latch came in the prop up the inside door panel while I worked.

Snapped new wheel on

Lifted out old silverware basket. Set new basket in. Took approximately 20 seconds.

I had to lightly pry off the long piece of plastic next to the wheel assembly because I had to twist the assembly counter clockwise to remove the old one. Also had to place the new one so that it rotated clockwise to seat it. Then replaced the other plastic piece.

I removed the screws around the top and halfway down the sides of the inside of the door. I found that you dont have to remove all 10 screws to access the assembly. Reach in and pulled out the assembly, there was enough slack to pull it out above the door. Pull the connectors off and slide the new ones on. Set the new assembly back in place, insert the 2 top screws first, and then the rest. That was it...very simple to change.