HDA1000Z11WH Hotpoint Dishwasher - Instructions

Identified solinoid responsible for the operation of the drain flapper valve had become damaged, possibly due to its coil shorting and overheating, the inside plastic insulation then melted and came up through the solinoid pin hole. I removed the tension spring holding the flapper drain valve shut, removed the eclip holding the white phenelic arm connected to the tension spring, removed the two screws mounting the solinoid assy. I threw out the bad solinoid. I then proceeded to install the replacement solinoid in reverse order of removal. The end. Works like a champ ! Thank you for your quick shipping response time. My wife is now once again happy. As you know, if my wife isnt happy, I sure wont be happy. :)

Opened package, removed cap and screwed it in place.

Removed the 6 screws and took off the inside pannel. Removed 2 screws that secured the timer.Unplugged old timer leads and put the new one in reverse sequence. Piece of cake.

Inspected the old gasket. Removed, cleaned, re-seated existing gasket. Tested and found smaller leaks. Purchased and installed new gasket. Majority of leaks stopped but some detergent still leaks. Unsure what the problem is with that but the main leaks have been fixed. Dishwasher is less than 5 years old. Thank You.

Turned off the electricity to the dishwasher,removed the old solenoid,and put the new one on(very easy),turned the electrical breaker back on.

REmoved the bottom to plates on the dish washer
removed the old solenoid put the new one in and
the washer was fixed. if i could replace it anyone
could do it.

I took the inside of the door off of the dishwasher and disconnected the timer, ordered the new timer and with a couple of screws and the attachment of 3 wires I was back in business! Now my dishwasher is working better than ever!

pulled out old motor. replaced new motor. works like new.

i couldent use the hole unit because it was for a dryer.

i new the motor would work because it had the same gear and rpm. i couldent find a motor no wear.

After removing the front panels, I removed two screws holding the valve in place. I turned off the water supply and removed the water line, unclipped the hose clamps and took the faulty valve out. I then reversed the above steps and turned the water back on. NO leak. Very easy to do andthe repair took ~20 minutes to complete.

problem solved..thanks

I took the bottom plate off by removing 1 screw on each side. I then pulled the water inlet valve out, disconnected the 2 wires. Because mine was the original inlet valve and GE changed the new one I had to remove the new inlet valve from the face plated and use the old face plate. I then reveresed everything and put it back together and Wah Lah the dishwaher was fixed!!

The finished accent panel on my GE dishwasher was dented and looked awful in my newly remodeled kitchen. I thought about purchasing a new dishwasher but instead searched the web for the part. Found Parts select and it was so easy to compare my part with the graph picture provided. Just count off the boxes for measurement and you will know if you selected the part you need. Access panel arrived in two days,packaged well, and I am happy to have found this website. Give it a try....and returns are easy too if you make a mistake in ordering. My order was perfect on the firt try.

took the moter off and the impellar off replaced the impeller .back and turn the washer back on but it still wouldnt .wash .the moter wouldnt turn .so had the moter tested and it was the moter . found out how and what to look for on you tube .it was a big help in how to fix your washer .typed in model and what kind portable .it was easy .thank you for haveing my part also .and shipping was real fast .

The repair wouldn't have taken as long as it did if the pictures on the installation sheet were clearer. They were very smudgy. Couldn't see the details on the pictures.

My old timer stopped rotating. Ordered this one. It showed up and the part number is off by one digit. Put the new one in, and the timer rotates fine, however water is no longer coming into the dishwasher. Put the old timer back in and manually rotated it and water comes in no problem. So we figured the old timer's electrical motor is burned out, and the new timer's signaling function is probably a bit different.

Turns out the motor is really easy to remove, just pry the metal latch out a bit with a flat screwdriver and out it comes. We put the motor from the new timer on our old timer, and presto, everything works!

Like other reviewers said here, pop off the seven screws and the interior door panel comes right off. Disconnect the power plug, signal plug and ground plug and reverse the procedure. Really easy repair. Make sure you shut off the fuse panel before starting the repair.