HDA1000Z11WH Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Bay Village, OH
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
water inlet valve stuck open (frozen??)
after watching related video on partselect.com, diagnosis and repair couldn't have been much simpler!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewellyn from Clarkston, WA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
No water fill to dishwasher.
Replaced the water-fill solenoid valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Bayside, NY
- Parts Used:
- WD08X10057
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Small leak at the bottom of dishwasher
Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the difficult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILLY from SAN LUIS, CO
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable)
Valve was leaking. This is the second one that has leaked.
Remove front shields on bottom of dishwasher. Shut off dishwasher and electricity. Unplug electric connection. Unscrew brace holder screws on front. Remove clamped on hose at back of valve. Unscrew valve from copper water pipe. Screw on new valve to copper water pipe. Put on clamped hose. Screw on bracket. Plug in electric connection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delia from Ocean, NJ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
no water was being supplied during certain cycle
door gasket dried out due to not using the dishwasher very often and needed to be replaced. removed door, replaced gasket, and re-installed door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELLIS from MADISON, AL
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
Water leaking from beneath dishwater
It took no time at all to identify where the water was leaking from. I accessed a parts breakdown illustration of my dishwasher, identified the part, ordered it and three days later my leak was fixed. Hose and water inlet valve assembly was easy to swap out. I estimate I saved myself about $150.00 by doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Willcox, AZ
- Parts Used:
- WD19X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Leaking motor seal
Followed easy instructions and completed repair in less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martin from chesterton, IN
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
water inlet valve wore out would not work
got replacement valve from part select and works like new this dish wash er is 24 years old. believe it or not did the job with pair of pliers and screw driver. used pliers to take off clamp and screw driver to take out 2 screws and replaced the valve the same way in reverse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Nespelem, WA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Wouldn't clean upper rack, not enough water
Checked the water supply to the inlet valve - OK, pulled the filler hose from the outlet side of the valve and checked flow in wash cycle. Results, less than 1/2 gallon. Checked your website, found 94% sucess rate by replacing the valve, so I ordered one. It took about 10 minutes to install with a nut driver, 6" adjustable to connect water supply, and plier to hold outlet clamp open to install it; now we look forward to dirty dishes rather than dumping water into the machine it takes care of itself and we once again get sparkly cups andglasses of the top rack. OU- Rah!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leanne from Divide, MT
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rinse aid fill cap was stripped.
I removed the old cap and put on the new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Corvallis, OR
- Parts Used:
- WD12X10284
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Old rinse aid fill cap broke off at base
I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bradenton, FL
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes cloudy, spotting
Unscrew old stripped out one and put in new one ..wala!! Easy repair for this old lady...
Was this instruction helpful to you?
Thank you for voting!