GSD1000-04 Hotpoint Dishwasher - Instructions

Simply remove both baffles by hand, wash space under baffles with warm water and dry, then insert new ones which fit perfectly and were tight.

very easy like you said

Remove lower panels, turn off hot water supply, Turn off breaker to dishwasher. notice how power connector is orientated and how valve is mounted to chassis of dishwasher and remove Molex connector which supplies power to valve. The power to the valve is 120VAC when the timer gets to the appropiate cycle I measured the valve with no connector attached with DVM set to Diode or ohms setting and got about .825. I measured the NEW part and measure about the same. Have towel under valve hoses for small amount of water will come out. remove small diameter hose , inlet water supply, remove 2 screws holding part with nutdriver to remove valve which exposes the black hose attached to valve. Hose has a hose clamp, use pliers to remove. good time to check and clean hoses. I unwrapped a coat hanger to run through the hoses for debris. to INSTALL reverse the above. clean water away from floor with towel. Turn on hot water supply, check for leaks, I did not have any leaks. Turn on breaker. You can stick a stubby screwdriver into the door close switch of front door which enables you to turn on (swing arm) dishwasher with door open to check water pressure. I have a great deal more water pressure and water from jets spray much higher than before. Old valve was clearly bad, but solenoid of valve still worked, which sucks in the arm when energized. I used a DVM on the 2 wire connector on valve to check for 120vac when cycle turns it on-measured good. I still don't have quite the same cleaning as before. It is 80% better, but something is still not right. My wife put in one of those pot cleaners (red) mesh plastic thingy on top rack--and found pieces of red mesh plastic in debris area, cleaned it out as best I could removing the 2 covers, but not sure valve is opening there or debris is clogged in there which sends pieces of food, etc. through hose to garbage disposal. Hose wasn't clogged. Cleaning better but wife is still saying not as good. The Pump is running good, cleaned dust and dirt out of pump with vacuum. 10 years old, thinking of removing dishwasher from counter and checking the pump area or change it.

Removed old lower spray arm, and replaced it with the new one.

I pulled the old basket out with my right hand and inserted the new basket with my left hand! HA! Maybe 5 seconds!

Just set it in as it was exactly as described and ordered.

Just plopped it in, it fit perfectly! I love it! Very easy to order the part, and very fast shipping! I order it and it took a day to get to me!

Just bought a condo in TN and the there wasn't any front wheels. Found your web site and ordered the parts.

I am a helpless old lady living alone. My dishwasher leaked......not bad at first. I put a towel in front of it. It got worse. I was adding towels each time I ran it. I asked my son to look at it. He said to find out where it was leaking from. I noticed it was coming from the right side. I looked and saw this thing (the real name was corner baffle) that looked kinda used up. I told my son what it was and he said go online and order it. I did. It came I took the old one out. It just lifted out. I cleaned all the debris out from where it sat with a toothbrush and put The new one in. Easy peasy. Don't need a grown son. I can take care of myself.

When I thought the dishwasher was leaking due to the drainage pipe, the repairman told me it was malformed door hinges instead.
I quickly place an order through PartSelect online. With the picture of the parts on the webpage, I was confident that the correct parts were ordered.
In less than 2 days, the parts arrived and the dishwasher leakage was resolved.

First I removed old baffles, they were filled with old, moldy, icky black stuff. I tried to clean them, but the ridges made it difficult to get everything out. I ordered new ones, ran the dishwasher without them just to clean out the unit, then installed the new ones, no tools required.

I put the part back on. It was simple to figure out. The wheels had been falling off for a couple of years and I kept putting them back on. This time the wheel broke and I went online to see if I could find wheels for my dishwasher. I received them and put it back on. Now I have a spare part in case it happens again. If this has been happening to you, I figured out that there is a difference between the width of the front wheels and the back wheels. Be sure before you order where the wheel came from. Mine are all falling off from time to time. So all the wheels are in different places now. The front wheels are wider than the back wheels or vice versa. Don't remember now. Just be cautious.

lifted out the 2 old corner baffles, ordered the new parts, set the new ones in their corners. No more leak! SIMPLE!

with thumb pressure just snapped the axle on shaft and then wheel on axle. as simple as that and i was done in about 5 minutes!

All I had to do was remove the wheel from the packaging and snap it into place on the end of the prong on the dishwasher rack.