GSD1000-04 Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Julie from Maumee, OH
- Parts Used:
- WD12X271
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheel broken off bottom rack
Open the tiny plastic package in inserted the wheel onto the "axle". Opened the dishwasher, pulled out the bottom rack and snapped the wheel onto the rack. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from The Villages, FL
- Parts Used:
- WD12X271
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rollers fell off lower rack of dishwasher.
First removed four old wheels. then attached four new wheels to lower rack by pressing into slots.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Mount Vernon, IL
- Parts Used:
- WD15X93
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Insufficient fill water, dishes not getting clean (valve diaphram had ruptured)
1. Remove lower cover skirt.
2. Shut of water at undersink valve.
3. Unplug power cord or turn off circuit breaker.
4. Disconnect water supply line from fill valve.
5. Unplug the electrical connector from the valve.
6. Remove the 2 valve mounting bracket screws.
7. With loose valve in hand, rotate to gain access to allow release of outlet hose clamp for hose removal.
8. Remove brass fitting from old valve and install on new valve. Use teflon tape on the pipe threads only.
Install new valve by reversing the procedure.
2. Shut of water at undersink valve.
3. Unplug power cord or turn off circuit breaker.
4. Disconnect water supply line from fill valve.
5. Unplug the electrical connector from the valve.
6. Remove the 2 valve mounting bracket screws.
7. With loose valve in hand, rotate to gain access to allow release of outlet hose clamp for hose removal.
8. Remove brass fitting from old valve and install on new valve. Use teflon tape on the pipe threads only.
Install new valve by reversing the procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Pattonsburg, MO
- Parts Used:
- WD8X228, WD8X227, WD35X10346
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher leaks from bottom of door......when operated.
Removed 7 screws holding "inner door" in place ( note: 2 bottom screws are different than the rest...keep separate).....remove rinse aid plug....press "tabs" inward to release rinse aid container. ( in this instance....the gasket had failed...which was "part" of the reason dishwasher was leaking during operation)
install new rinse aid container ...making sure that "trip arm" is positioned correctly........and press into place. ( Tabs should expand when container is properly positioned...creating a tight seal).....reuse old rinse aid filler plug.
Replace "inner door" cover....tighten screws.....
remove faulty tub corner baffles....place new ones in corresponding positions ( the baffles form a suction .....to stay in place....no adhesive needed)
Close door and operate as usual........no more leaks!
This is a super easy "no brainer"...that would have cost about half the price of a new dish washer ...had I hired a "professional" to do the repairs!!!!
install new rinse aid container ...making sure that "trip arm" is positioned correctly........and press into place. ( Tabs should expand when container is properly positioned...creating a tight seal).....reuse old rinse aid filler plug.
Replace "inner door" cover....tighten screws.....
remove faulty tub corner baffles....place new ones in corresponding positions ( the baffles form a suction .....to stay in place....no adhesive needed)
Close door and operate as usual........no more leaks!
This is a super easy "no brainer"...that would have cost about half the price of a new dish washer ...had I hired a "professional" to do the repairs!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Elmendorf, TX
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Basket was lost
Opened package from Parts Select.
Removed Silverware basket from package.
Opened Dishwasher.
Inserted Silverware Basket in rack.
Closed Dishwasher.
Discarded shipping package.
Told wife I fixed Dishwasher.
Sat down & had a beer.
Removed Silverware basket from package.
Opened Dishwasher.
Inserted Silverware Basket in rack.
Closed Dishwasher.
Discarded shipping package.
Told wife I fixed Dishwasher.
Sat down & had a beer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald from Hamilton, NJ
- Parts Used:
- WD12X271
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rollers broke off from bottom rack of dishwasher
Went to www.PartSelect.com. Part was easy to locate online with GE model number and illustraion online. They shipped the parts in two days and I put the new parts on by hand. Saved a $135 service call from GE. One part came in broken from the factory. Upon calling customer servce, PartSelect sent out a replacement part the next day - no problem. Great service, would be happy to use again - Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Polson, MT
- Parts Used:
- WD15X93
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Little/no water coming in & dirty dishes
1. Remove access panel under door. 2.Shut off hot water.3. Shut off electric to washer.4. Disconnect water line from water inlet valve.5. Remove small outlet water line from valve. Replace valve & reconnect. OR !!! 1.Take solenoid valve & bracket off of original inlet valve 2. Pull out white plastic diaphragm cover. 3. Remove diaphragm & clean out water holes with a pin. 4. Reassemble valve. 5. Reinstall original water inlet valve & save $27.00
Was this instruction helpful to you?
Thank you for voting!
tub corner baffles were falling apart
I opened the D/W door, used needle nose pliers to remove the old baffles. They come right out. I cleaned the area using paper towels and installed the new baffles. They just sit in the corners with nothing holding them. Simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Willmar, MN
- Parts Used:
- WD22X135
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Dishwasher leaked at bottom of door.
I first assumed that the leak was from the door gaskets getting old (unit is near 25 years old). Therefore I replaced the door gasket and two bottom corner gaskets first (no tools needed, took about 15 minutes). All gaskets remove easily and the new door gasket "snaps" back into a groove. Pay attention to how the bottom corners of the door gasket are installed. The bottom corner gaskets simply fit back into their openings. But, leak continued. Further investigation revealed the lower offset spray arm had worn out and had a big hole in the bottom of it, which was spraying water up through the bottom lip of the door. It took about 15 minutes to replace the arm, by simply unscrewing the spray tower (reversed threads - using only my hands). Problem solved, unit cleans much better. I hope to use it a few more years until a major kitchen remodel fits my budget.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felix A from Orlando, FL
- Parts Used:
- WD12X271
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing wheels
Inserted wheels on socket and then into the dishwasher rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Dallas, TX
- Parts Used:
- WD15X93
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set, Wrench set
Thanks for sending the correct part. You guys did a great job.
Just put the part on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donald from fullerton, CA
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Silverware basket was missing in the condo that we rented
I just plugged in the model number and a screen came up that showed all the part numbers that made up the model. picked out the parts that we needed and ordered it and within 2 day we had the new basket that we needed for our dish washer.
the service and ease was better that going to the appliance store and picking up the basket.
I was very happy the the service.
Donald Brown
the service and ease was better that going to the appliance store and picking up the basket.
I was very happy the the service.
Donald Brown
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph Raymond from Gansevoort, NY
- Parts Used:
- WD12X271
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
The wheels kept falling off the lower carriage in our dishwasher.
Each replacement wheel came in two parts: the wheel itself and the clip which had to be pushed through the center hole in the wheel in order to attach each wheel to the carriage that holds dishes. I had difficulty assembling the clips and wheels until I ran the clips under hot water to soften them. This made it possible to assemble the wheels and attach them to the dish carriage. I would have preferred the wheels to have come assembled, particularly given the price of each one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Friendswood, TX
- Parts Used:
- WD12X271
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rollers were missing from front of the rack
The new rollers snapped into place on the rack, by simply pushing them in. I was able to do it by hand, my wife could not do the same, so you might use some pliers.
Was this instruction helpful to you?
Thank you for voting!