GSB2800E*116 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from Oakdale, NY
- Parts Used:
- WD28X10103, WD24X214
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Leaking from the hose that connects to the upper spray arm
replaced hose and upper sparay arm
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kurtis from Morristown, MN
- Parts Used:
- WD28X10103, WD24X214
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Leaked from the top of dishwasher
Used a nutdriver to remove the two screws attaching the third level spray arm and a pliers to release the clamp holding the power shower hose. Reversed the process on the new hose and spray arm. Dishwasher works great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Avondale, AZ
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher would not drain completly
Remove filter screen at rear bottom of dishwasher with 1/4 in socket, remove check valve by hand, install new check valve, reinstall filter screen. Run a load of dishes, drained completly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Macon, GA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Food particles left on dishes after every wash... Piston and Nut Assembly was completely worn out (disolved) and leaking dirty water back into the rack area instead of draining it.
Unscrewed 4 screws from the back, bottom of the rack area which hold the cover. Twist out the old Piston and Nut which is threaded to fit securely (needed some elbow grease to get the old one out). Twist the new part in and place the cover back in place with the 4 screws. Done. Dishwasher works like it was brand new. Cleanest dishes in the country... ;)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from port clinton, OH
- Parts Used:
- WD15X93
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
when dishwasher was turned on no water sprayed out the rotating arm
I diconected the electric removed water line removed 2 hex head screws pulled out inlet valve squeezed the pressure clamp and pulled off water inlet line and re assembled very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Chalfont, PA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dishwasher not draining, water left in bottom when cycle completed
Thought hoses were clogged. Cleaned hoses but no obstructions. Googled the problem and found many similar problems. On PartSelect, the Piston and Nut Assembly was found to be the problem 44% of the time. I ordered the part and it arrived two days later. PartSelect showed how to install it and the problem was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Stoughton, MA
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I was very disappointed in the in-the-door silverware basket most dishwashers are equipped with today and longed for the ones that have been phased out.
I went to PartSelect online and easily found an exact duplicate of my old basket at a reasonable price. I ordered it, expecting delivery in about 3 - 5 days. It was on my doorstep 2 days after the order was placed. I opened the dishwasher door, set it in the place of my choice, and what a timesaver! Try it! You'll like it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Shreveport, LA
- Parts Used:
- WD24X214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench (Adjustable)
water keaking fron tip of dishwasher around the showerhose
Laid dishwasher on its side to get to the bottom very easily, unscrew the screw that was holding the bottom of the hose to the dishwasher, then remove the 2 screws in the top of dishwasher that is holding the shower hose in placeinstall new hose in reverse, very easy .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott Allen from Clarklake, MI
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Standing Water In The Tub After The Wash Cycle Has Ended, The Problem Is A Worn Or Missing Rubber Seal On The Piston Nut Assembly, It Is Easy To Tell If It Is Indeed This Problem By Feeling The Pump Discharge Line When The Washer Is Draining You Should Be Able To Hear And Feel It Pump The Water Out
Took of the plactic strainer shroud unscrewed the piston nut assembly by hand installed the new one it takes longer to remove the shroud than it does to replace the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Hopatcong, NJ
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher not draining completely
This was a piece of cake! Simply removed the rear drain cover with a nut driver and unscrewed the piston from its seat. I noted that the seal in the old piston had deteriorated over time. I rubbed a little petroleum jelly on the upper gasket of the new piston and simply screwed it into place, solving the problem entirely. Could not believe how quickly the part was delivered - next day!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Courtney from Lancaster, PA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher not completely draining
Followed the video on the website - seriously easy. took me 5 minutes and solved the problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from New York, NY
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing silverware basket
part came in the mail and fit the missing space perfectly. no complaints. easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Hawthorn Woods, IL
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher was not draining.
The dishwasher would drain correctly 3 out of 4 times and the original part did not appear to be in bad shape. Decided to change anyway based on posted success rate in resolving the issue and the low cost of the part. After one month of daily operation the issue has been completely resolved. Could not have been any easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Fort Myers, FL
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rack had rusted through in several areas.
Pulled out the old and rolled in the replacement. The easiest part of the repair was ordering from the PartSelect website and receiving it via FedEx Ground the next day. Thank you PartSelect. Even my husband could have been successful with this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from woodbridge, VA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Water would not drain after cycle
After reading some of the suggestions I couldnt beleive it was that simple and easy. So I ordered the piston and nut assembly, installed it in less than 15 min. and after a rinse cycle test the problem was fixed. Thank you all for this wonderful site.
Was this instruction helpful to you?
Thank you for voting!