GLD5660V00SS General Electric Dishwasher - Instructions

just slid the new rack into place

I removed the old seal, cleaned behind it, and then put the new seal in. We saw a video on You Tube on how to do it. Partselect also sent instructions on a e mail with the order receipt. We enjoyed working with you guys. Your customer service representative was very nice and accurate in sending out the part. All went as she said it would. Thanks!!

After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.

The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.

I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish washer, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.

Removed inside of door, slide bottom seal on and put inside door back on. Job done!

Watched the video, and followed the directions. Although my machine had some slight differences, the repair went pretty much per the video. Got all connections back where they belonged, cleaned up the insides a little while had the door parts separated, then buttoned it all back up, ran a cleaning solution thru empty washer, let it dry then started filling with dishes and ran the wash cycle the next day when full. All is well.

shut off water. removed lower panel disconnected power removed supply hose and outlet hose. disconnected electrical plug from valve. Un bolted valve from frame. removed elbow from valve inlet. installed elbow on new valve using Teflon tape. reinstalled valve to frame. connect hoses + electric plug to new valve. turn water on check for leaks. reconnect power. run dish washer check for leaks & popper operation. reinstall lower panel.

Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.

Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.

Repaired the soap dispenser.

I called your tech and she sent me a awesome video that made it so easy to fix on my own

Pulled the old one out and placed the new one right into place

two screws, two minutes, all done

Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.