ADB3500AWS41 Amana Dishwasher - Instructions

first, i removed the inner door panel exposing the latch assembly. i then disconnected the wiring to switches noting their locations. removed and replaced with new latch assembly, connected all wiring back to their corresponding switches, assembled the inner door panel and checked to make sure the latch was working properly.

First, shut off the circuit that the dishwasher is on. Remove the 10 - 12 screws that secures the inside waterproof panel to the door. There are two electrical connections are either side of the handle (latch assembly) that need to be removed. No need to disconnect any other connections or reservoirs. The handle comes right out. Seat the new one in door front opening. Reconnect the electrical leads and reseat the interior panel. I would put in the 2 screws are either side of the handle first; then the 2 at the bottom on either side and then the remaining. This is a very easy DIY job.

After only 2 years, the Amana dishwasher door began to stick severely. If finally stuck so bad that I had to break the handle to get the door open. The replacement latch and handle fit perfectly and it only took a few minutes to get the screws off of the inner door panel to access the broken latch.

Removed inside cover.
removed part.
disconnected switches.
plugged wires onto new part.
placed part in.
put inside cover on and screwed down.
Note: be careful of the bottom of the inside cover.

First I removed the screws from the inside of the door exposing the latch assembly. Removed the old part and installed the new assembly. Don't screw it on to the door untill the cover is on again.
First I ordered only the latch without the handle. Found after opening it up the handle was broken on the inside so had to order the assembly. It's a piece of cake to install. If you're having touble opening the door don't think because the handle looks ok from the outside it's not broken.. probably is. Partselect.com is the greatest company to deal with. I'd recommend them to anyone and have.
Sam

Ensure to order part # PS1559543, which is the complete assembly although the diagram doesn't show this, and not PS2100626 which doesn't include the handle. The new assembly is a different style than the original therefore you should replace the complete assembly.

This was an easy fix. Remove the eleven torque screws on the door and separate the inner door panel enough to remove the old assembly. Remove the wire connections from the door switches, reconnect to the new assembly, and reinstall the assembly and inner door panel.

Took a while to figure out what had to be done. Brackets have to go under the metal frame which involves dropping the compartment. That is done by removing the screws which are hidden under the door gasket. Once I knew what had to be done it was simple.

After receiving the latch assembly, which arrived rather quickly, I found the handle itself was not enclosed in the package. Therefore this repair was delayed and after several calls to the 1-800 number I was informed the company had discontinued the distrubution of the handle. They offered a full refund, however I'm still waiting for the return labels so as to ship the latch back.

Now on the brighter side, the company representative put me in touch with a local distributor that did carry the latch/handle assembly as one piece and for a lot less money.

For those who are attempting the repair, don't worry, It was very simple. Just remove hex screws, lift the inside panel, unplug the two connectors and insert the new assemply.

Must say my wife was very happy to have the dishwasher up and running again.

Good luck !

Removed screws. New Part does not come as an assy. Need to order handle. Other sights offer full assy for less.

I bought 2 Maytag appliances, a microwave and a dishwasher - they are both crappy!

The top plastic spray arm kept falling off into the top shelf of the dishwasher, causing all of the glasses on that shelf to come out dirty.

The arm has a small bracket that can snap off and on the main water tube easily without tools.

Changing it was a snap!

All I had to do was litterally snap the wheels into place..it was so easy and so cheap!

Removed ~12 screws holding the inside liner onto the door. Pulled off the two connectors (one with black and one with white wires). Replace the handle and latch mechanism. Redid connections and replaced screws. Viola. (Be sure to buy BOTH the handle and latch mechanism- I don't see how you could easily install the handle on the mechanism myself, and what broken in my case was the black handle).

The upper arm assembly removes easily by unsnapping a plastic part or two that holds it in place.
Once the arm assembly is removed, you simply remove the screw that holds the arm on, replace the arm, and replace the screw. The key thing here is that you need a "star drive". This is a screw driver or bit that has a star shaped end. I don't know what size it is.

The plastic wheels on the upper and lower racks keep breaking. The latest casualty was also chewed up by the dog(s). They just pop right on the posts, a simple 2-second fix. I ordered the parts on a Tuesday morning, standard shipping, and they arrived FedEx less than 24 hours later. They came from Peoria, and I live about 1 hour away in Bloomington. Very pleased with the service. Will order from PartsSelect again if I need parts for any other appliance that I can fix myself.

This couldn't have been easier. After unsnapping the docking station from the dishwasher, I aligned the two flapper valves that come with the unit and pressed them into place. I then pushed the new unit into place by pushing first on the left side and then the right until it clicked into place.
I looked at the old one and found that one flapper was gone and the gaskets were deteriorated. What made the whole process easier was buying from PartSelect. I have bought from them before and will again.