C201 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Duane from Niceville, FL
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
smell of a dead animal
The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from Bothell, WA
- Parts Used:
- 12200035
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Cleaners lost knob.
I pulled off the other 3 old knobs. Pushed on the new ones, which pushed on hard, but work. They stick out farther than the originals. They look a little different, but only to me. No one else would notice.
The main part is, it works. A little spenty for my taste, but did not know where else to go and they arrived very quick.
The main part is, it works. A little spenty for my taste, but did not know where else to go and they arrived very quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Kingwood, TX
- Parts Used:
- WPY04100165, 715878, 715877
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
small burner only heated intermittently.
Unplugged old burner element, plugged in new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JANE from BALTIMORE, MD
- Parts Used:
- 12200035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem...just wanted a fresh look
our cook top is so old, but no need to replace just yet. so I ordered new knobs to get a new look
thank you!
thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirlely from Citrus Heights, CA
- Parts Used:
- 12200035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken burner knob
removed all for knobs and replced with new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from San Antonio, TX
- Parts Used:
- 12001676
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Burner wouldn't heat (wiring failure)
1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from FRESNO, CA
- Parts Used:
- WP71003558, 715396K
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set, Wrench set
Downdraft blower motor noise, fluctuating fan speed and binding. Also replaced indicator light for burner knob.
1. Turned off electrical breaker at electrical service panel.
2. Tested stove top to verify correct breaker was off as well as cook top.
3. Removed front electrical connection panel @ cook top.
4. Disconnected wires to blower fan. (Before disconnection I color coded wires for correct reconnection)
5. Removed the bracket holding the armored cable (protecting motor wires) and removed wires (where connects to electrical connection box).
6. Removed 4 nuts @ blower motor housing and removed blower motor housing and fan.
7. Removed 3 screws that attached the blower fan to the blower motor housing noting or marking the position of the housing to the motor bracket in order to have the same placement position.
8. Pulled the 3 connecting wires from the armored cable protector to separate housing from motor.
9. Removed the fan assembly from the blower motor shaft by using an allen wrench carefully noting the distance from motor face to the fan.
10. Noting/marking the position of the motor mounting bracket connections unscrew the nut and screw that secures the bracket to the motor.
11. Reassemble in reverse order.
Note:
I taped the motor wires tightly together every 3 or so inches to be able to slide through the armored cable.
I also had to rotate the mounting bracket a little to be able to perfectly match the motor housing to the motor bracket.
The new fan motor works great but it's a little bit louder.
2. Tested stove top to verify correct breaker was off as well as cook top.
3. Removed front electrical connection panel @ cook top.
4. Disconnected wires to blower fan. (Before disconnection I color coded wires for correct reconnection)
5. Removed the bracket holding the armored cable (protecting motor wires) and removed wires (where connects to electrical connection box).
6. Removed 4 nuts @ blower motor housing and removed blower motor housing and fan.
7. Removed 3 screws that attached the blower fan to the blower motor housing noting or marking the position of the housing to the motor bracket in order to have the same placement position.
8. Pulled the 3 connecting wires from the armored cable protector to separate housing from motor.
9. Removed the fan assembly from the blower motor shaft by using an allen wrench carefully noting the distance from motor face to the fan.
10. Noting/marking the position of the motor mounting bracket connections unscrew the nut and screw that secures the bracket to the motor.
11. Reassemble in reverse order.
Note:
I taped the motor wires tightly together every 3 or so inches to be able to slide through the armored cable.
I also had to rotate the mounting bracket a little to be able to perfectly match the motor housing to the motor bracket.
The new fan motor works great but it's a little bit louder.
Was this instruction helpful to you?
Thank you for voting!
worn out parts
Everyone was amazed we could still get parts for our 25 year old Jenn-air stove top. Easy installation, hands only, couldn't be happier with the easy of ordering, the fast shippment, the quick replacement. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lora from SEBASTIAN, FL
- Parts Used:
- 12200035
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Origin knobs cracked
Just slip new knobs on. Simple and works great!!
Was this instruction helpful to you?
Thank you for voting!
install burner drip pans
Did not need tools for this job. Simply lift burner element and remove old drip pan and put new one in its place. However - the drip pans that were shipped only fit on the left side of the range. The right side, where the grill attachment goes, is so shallow that the drip pans on that side hit the bottom plate beneath the burner element and would not let the element go down far enough to seat properly. I kept the two pans that don't fit for extras, but I still need shallower pans to fit on the right side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colette from Baton Rouge, LA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old filter to replace
:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
old, crusty drip pans
This was so easy. I've looked for years in stores for these pans. I finally tried the Internet, found PartSelects and, holding my breath at what i'd find, voila'...perfect fit, perfect replacements. And it took just a couple days to arrive. I'll definately be back!
/John
/John
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royce from Garland, TX
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs were worn badly
Pulled off old knob, then pressed on the new one.
It was very easy, and the part was the correct one.
It was very easy, and the part was the correct one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from Fayetteville, NC
- Parts Used:
- WPY04100166, WPY04100165, 715878, 715877
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old stove drip bowls needed replacing
Removed heating elements and dropped new drip bowls in and replaced new elements
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from NEENAH, WI
- Parts Used:
- WPY700854
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Numbers on surface burner knobs were illegibel.
I also sprayed them 3-times with a clear coat before installing. The clear coat I purchased at WalMart once I noticed it claimed to be safe for plastic. Avoid a clear lacquer based product.
Was this instruction helpful to you?
Thank you for voting!