C201 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
surface unit infinite switch needed replaced. The knobs and lens were cosmetic.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires and replaced the connections in sequence. It was easy. BUT, be sure the circuit breaker is disconnected if you want to enjoy the fruits of your labor. I figure I saved about $1100 by not having to buy a new stove top and I now have an almost new one. The cook appreciates it too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from SOUTHBURY, CT
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Jennair cooktop with coils lost one of its coil guides.
We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CONCORD, NC
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Burner plugs were loose
used the supplied parts...very easy. The parts were exact replacements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lenice from Stuart, FL
- Parts Used:
- WPY700854
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Elec. stove-top knobs (imprinted with HI to LO numbers 1 to 10)worn to non-readable.
Knobs sent fit the shafts, but due to molded internal stop wouldn't seat. Had to drill out the stop, and also file down the shafts a bit for knobs to seat acceptably closer to stove-top.
Was this instruction helpful to you?
Thank you for voting!
Could Not Use One Burner
Turned power to stove off. Removed two screws from cover - lifted cover up and pulled switch out and disconnected wires. Put new switch in and connected wires. Made sure that it was in correct position by placing knob on to make sure off position was correct - then placed plate in position and closed - put two screws back on plate and put new knob on. Turned power back on and turned knob and burner back in operation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veronica from East Sandwich, MA
- Parts Used:
- WPY707453, WPY04100166, 715878
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Burner not wrking well and did not fit well anymore. The whole burner was slippig when cooking withit.
Took out the old element, ring and drip and replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alphonso from plainfield, IL
- Parts Used:
- WP71003558
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
blower motor was making loud noise
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
Was this instruction helpful to you?
Thank you for voting!
burner receptacle was broken
The repairs were very simple we just disconnected one screw then removed the old one and replace with new one. The left side took a little longer, because of the 8 screws we needed to remove to take the back panel off. But once we had it taken off the replacement was a snap. Nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from Atascadero, CA
- Parts Used:
- WPY04100165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
center piece of the heating element broke off
so easy, just ordered the part, the part came and inserted the element into the stovetop
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Brooksville, FL
- Parts Used:
- WPY707453
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ring adapter was the original and was pretty well worn through.
Removed the old adapter and replaced it with the bright and shiny new one that fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
Drip pans were in need of replacement
No brain surgery required. Removed electric burner, put in new drip pans. Voila! Good for many more years of service looking like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martyn from Middletown, OH
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Oceanside, CA
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My electric range burner was not heating.
All I had to do was remove the old burner and push the new burner into place. It couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Portsmouth, NH
- Parts Used:
- WPY707453, WPY04100166, 715878
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Adaptor ring and drip bowl corroded over the years and the heating element was acting up.
I removed the old heating element, then the drip pan and then the adaptor ring. I cleaned the residue and buildup that was under the ring and on the surface below, I then snapped in to place the adaptor ring and then oriented and placed the drip bowl in place and finally oriented and pushed the heater element leads into their socket.
I turned the heating dial on and immediately felt the element warming up.
Checked Low temp and then Hi temp.
Everything is working and looking fine. The wife wants to replace the other ones, she says that it's easier than cleaning them.
I turned the heating dial on and immediately felt the element warming up.
Checked Low temp and then Hi temp.
Everything is working and looking fine. The wife wants to replace the other ones, she says that it's easier than cleaning them.
Was this instruction helpful to you?
Thank you for voting!