Yard Machines Parts

Fix Number

FIX16463287

Manufacturer Part Number

942-04308A

★★★★★

★★★★★

4 Reviews

Fix Number

FIX9988561

Manufacturer Part Number

647-04271-0637

This is an authentic manufacturer-sourced replacement part which is specially designed for use with Craftsman lawn mowers. The grass bag frame supports and hold the grass bag in place, while it is collecting grass clippings. To install or replace the grass bag frame requires no tools. This part is made of metal and is sold individually.

Fix Number

FIX9110822

Manufacturer Part Number

738-04124A

Designed for use in MTD, Yard Machine, Troy-Bilt, Yard-Man, and Craftsman machines, this OEM approved Shear Pin fits a variety of models. For full compatibility, please see the "Model Cross Reference List" below. This is a shear pin for your lawn and garden equipment, most commonly your snow blower. It is designed to snap if your auger gets jammed or clogged, to protect your snow blower from further damage. Because this part is meant to snap at a certain point of pressure, it is a commonly replaced part in snow blowers. Consequently, we recommend keeping a spare on hand. This Shear Pin is approximately 1.75" long, and is sold individually.

Fix Number

FIX11813755

Manufacturer Part Number

954-04060C

This is a Genuine Manufacturer Approved replacement V-Belt used on Riding Lawn Mowers. This part is made out of Rubber and it is sold individually. This is the Belt that drives the Blades. Clean the pulleys off before installing the new belt to ensure top performance and longevity with your new belt. Inspect belts periodically and replace them when worn to maintain peak performance.

Fix Number

FIX9118299

Manufacturer Part Number

753-06183

This is an authentically sourced fuel tank assembly, including the fuel lines, fuel cap, fuel filter, and screws needed for assembly. This fuel tank assembly is for trimmers, and is where the fuel is filtered and stored for use with the engine. Due to its constant contact with fuel, especially if fuel has been left it in for extended periods of time, it may crack, in which case it should be replaced immediately. Leaking gas is very dangerous, so it is important that it get fixed quickly. Before beginning this repair, drain the gas from the tank before installing the new one.

Fix Number

FIX9096195

Manufacturer Part Number

714-04040

This bow tie cotter pin fits snow blowers, as well as other gardening tools. The pin helps secure the auger to the shaft on a snow blower. Due to constant wear, this is a commonly replaced part. Tip: Extra pins are recommended. *Please note: this part is sold individually. For installation instructions, refer to the diagram provided by the manufacturer.

Fix Number

FIX16424685

Manufacturer Part Number

749-05084B-0637

This replacement handle is a genuine OEM sourced part. It is specially manufactured for walk behind and push lawn mowers. Upper handle allows user to control the lawn mower. It is attached to the lower handle assembly that is sold separately. This part is made out of metal and is sold individually. Please note, the control bar, knobs and cables are all sold separately. You will need a wrench to replace this upper handle. • Disconnect the bail bar • Detach the control cable • Remove the bolts and the nuts that secure upper handle • Secure the new handle using the same hardware • Reattach the bar and the control cable

★★★★★

★★★★★

1 Review

Fix Number

FIX11813377

Manufacturer Part Number

946-05124A

This is an authentic OEM part. The MTD deck engage cable is composed of metal and plastic parts, and has been designed for use in several tractor machines. This part is fastened onto the frame assembly. The deck engage cable works to move belt idler pulley and engage the cutting blades. Please refer to manual for specific repair instructions. A wrench and a screwdriver is helpful in making the replacement. This part is sold individually.

Fix Number

FIX19305064

Manufacturer Part Number

946-04661A

This is an authentic 51-inch control cable for walk-behind lawn mowers. This part is made up of a metal wire cable with a Z-type bent end on either side, and a 37.5-inch rubberized outer cover. When the control handle is released, the control cable stops the blade. If the cable breaks, the brake will not release even after pressing the lever. To remove the old cable, cut off any cable ties, remove the cable end from the control bail, and remove the control cable from the engine (you may need pliers). Remove the cables from the openings on the handle, which can be twisted off by rotating the cable at a 90-degree angle.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX9903219

Manufacturer Part Number

17211-ZL8-023

To ensure your engine is protected, it is vital that the air filter is inspected regularly and replaced according to the manufacturer recommendations. This filter helps to prevent dirt and dust from making its way into the carburetor and damaging the engine. If the engine is not functioning as it should, this should be one of the first parts you check. To inspect the filter, you will need to remove the air cleaner cover, and lift the filter out of place to remove.