Yard Machines Lawn Mower Parts
Start With Your Model Number
Popular Yard Machines Lawn Mower Parts
Fix Number FIX9169783
Manufacturer Part Number 942-0741AThis is a mulching blade for your lawn mower. It is located underneath the lawn mower deck, and cuts the grass by rotating. This blade has a curved style shell, and includes extra cutting surfaces along the edges of the blade. If installed correctly this part will keep the grass clipping under the deck longer, and re-cut them. The blade is 21 inches long, and sold individually.
Fixes these symptoms
- Mower blade does not cut
- See more...
Bell Blade Support
Fix Number FIX9119111
Manufacturer Part Number 736-0524BThis is a bell blade support, also known as a bell spacer, for your lawn mower. It is fitted between the bottom of the blade, and the blade bolt. This part provides support for the blade. It is made of metal to ensure a long life. If there is visible damage or wear, replace this part.
Michael from Lillian, AL
Blade became warped over time, baffle was falling downIn order to change the blade in a push mower you need to use a 2x4 or equivalent to stop the blade from spinning. I bent the blade back previously by heating it up but I think it was causing too much vibration so I got a new blade after hitting stumps over the years. I run some things into the ground. The spark plug is amazing and really high quality. Its a simple change. The drive belt is also a simple change, any 6 in 1 if you remove the screw heads will have the right nut sizes for most mower parts. Always lube up the belt "like two drops" with a little belt oil and it will last longer. I use diesel oil, 3 n 1, or chain saw bar lube oil. The tensioner for the belt is an easy adjustment. This model is also prone to fuel lines being blocked. Just detach the fuel line, blow it out with your mouth, and reattach. Have had it happen twice in 10 years, some people would be pulling spark plugs, diagnosing the engine, etc, its pretty easy, just put some fuel on the carb to see if your getting fuel blockage. Read more...
Nut, Flange Lock, 1/4-20, Grf
Fix Number FIX9299574
Manufacturer Part Number 712-04064This is a flange lock nut, and it is used with various outdoor tools and equipment. The flange lock nut is all one piece. It has a bottom circular flange and a smaller top hex section. This is a torque type lock nut, and it has no temperature or chemical restrictions. This part has a 1/4-inch diameter and 20 thread size.
Fix Number FIX10033626
Manufacturer Part Number 942-0741AThis is an original manufacturer mulching blade for a lawn mower and it is sold individually. This blade measures 21-inches long, making it compatible with 21-inch decks. The blade will wear over time, it can rust, chip, warp, especially if it has hit a large object. If you notice it is tearing the grass and not cutting efficiently, this is a common symptom of a damaged or dull blade. For this DIY repair, start by disconnecting the spark plug from the boot and turning the mower on its side, making sure the air filter and carburetor are facing up. Remove the bolt and blade bell support and then remove the blade from the adapter. You may wish to lubricate the engine crankshaft and the inner surface of the blade adapter with light oil. Next, place the blade adapter on the crankshaft. Put the blade on the adapter, making sure the side of the blade that is labelled with the word bottom (or with the part number) is facing the ground while the mower is in proper position. Double check that the blade is aligned properly and seated securely on the blade adapter flange. Place the blade support on the blade and align the holes on the blade bell support with the ones on the blade. Replace the hex bolt and tighten to the manufacturers recommended torque.
Lawn Mower Zone Control Cable
Fix Number FIX9180334
Manufacturer Part Number 946-1130This zone control cable is for lawn mowers. Zone control cable stops the engine when you let go of the handle. Wear work gloves to protect your hands during this repair.
Joseph from San Jose, CA
Broken control cable and handleReally straight forward, can be done without tools. Great price for parts and job done for less that half of what it would cost to have a shop do it. Even a lazy teenagers can do it....:) mine did:) Read more...
Fix Number FIX9311087
Manufacturer Part Number 936-0119This lock washer is used to resist the loosening of bolted joints. Repair tip: It is difficult to install the lock washer in a tight place or when the bolt/screw is pointing down. This lock works with the following appliances: Lawn tractor, tiller, chipper, shredder, lawn mower, snow blower, leaf blower/vacuum, log splitter, edger, hedge trimmer, and engine. Refer to the manual provided by the manufacturer for repair instructions.
Nut, Flange Lock, 3/8-16, Grf
Fix Number FIX9095080
Manufacturer Part Number 712-04065This lock nut is used for lawn and garden equipment, and is sold individually. This nut resists loosening when it is correctly threaded onto a bolt in your tool. The measurements are: the diameter of the bolt hole is 3/8 inches and the thread count is 16. For instructions on where the lock nut is located in your tool refer to the manual provided by the manufacturer.