OEM Andis Clipper Trimmer Parts & Accessories

Switch Button

$5.95

Fix Number: FIX17016561
Manufacturer Part Number: 69136

This is an authentic replacement part manufactured for Andis clippers. This molded rubber switch button is the cover seen from the side of the clipper, when pressed the button engages the circuit board. Overtime the switch button can wear exposing the circuit board, it is recommended to replace worn switch buttons. The switch button is sold individually, and the circuit board is available separately.

Tension Spring Assembly

$5.95

Fix Number: FIX12164188
Manufacturer Part Number: 201394

This part comes directly from Andis. This Tension Spring is used in multiple models of Andis hair trimmers. The Spring is made of metal and includes the nylon tip. The Spring holds tension on the cutter of the blade. If the blade doesn't move, then this part should be replaced. This part is commonly purchased with the Tension Screw (part number 32527) and the Retaining Screws (29752). Tools Used: • Flat Head Screw Drivers • Philips Head Screw Driver

Blade Lock Latch

$5.95

Fix Number: FIX12006498
Manufacturer Part Number: 64537

This part comes directly from Andis. This Blade Lock is used on many Andis clippers. This part is black and made of metal. It is used to hold and lock the blades into place. It is common for the hooked tip to break after a time. It is recommended to purchase a couple of these Locks at one time. The Lock is easy to replace. Remove the two Philips Head Blade Hinge Screws (part number 27864). Remove the Hinge Assembly (S63897) and align the spring with the holes on the new Lock and reinstall. Tools Used: • Screw Driver

Carbon Brush With Wire Lead An

$5.95

Fix Number: FIX12006404
Manufacturer Part Number: 27847

This is a genuine OEM sourced replacement part designed for use with Andis clippers. This assembly includes one (1) carbon brush with a lead wire attached. Please note brush spring and retaining clip are both sold separately. Due to normal use and friction brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • First remove cover • Take our old brushes and replace them with the new ones • Secure the cover and test the tool

Hinge, Bgc/bgrc

$22.88

Fix Number: FIX12006409
Manufacturer Part Number: 28194

This part comes directly from Andis. The Hinge is used on multiple models of Andis hair clippers. The Hinge holds the blade into place allowing the Blade Drive to move the cutter on the blade back and forth. The Hinge should be replaced if it no longer has enough tension to secure the blade. To replace the Hinge two Philips Head Screws need to be removed. Once they are removed replacing the hinge will be simple. Tools used: • Philips Head Screwdriver

Switch Assy-ml/gc-service

$5.95

Fix Number: FIX12006211
Manufacturer Part Number: 01767

This is a genuine high quality switch assembly that is sourced directly from original equipment manufacturer for use with Andis clippers. It is the part of the tool that allows user to turn the unit on and off. Over time mechanical switches will wear out and may begin to fail eventually requiring replacement. Replacing it is a simple task that should only require a screwdriver. One durable plastic switch with two lead wires attached is included per order.

Pc Board, 1-Spd 120V Agc/Bgc

$22.51

Fix Number: FIX12006329
Manufacturer Part Number: 22682

Power Cord (14-foot)

$20.27

Fix Number: FIX12006469
Manufacturer Part Number: 64250

This is a genuine manufacturer approved replacement power cord used with Andis clippers. If the cord is damaged it is important to replace it before continuing to use the tool. This cord is sold individually. Please note the cord protector/sleeve is included. To complete this repair you would need a screwdriver.

Pc Board, 2-spd 120v Agc/bgc

$25.15

Fix Number: FIX12006328
Manufacturer Part Number: 22681

This is a genuine Andis part. This PC Board is used in many models of Andis clippers. The Board is configured for two speeds. This part should be replaced if there is no power getting to the motor. One indicator that the Board has gone bad is if the resistor is discolored or burned out. Other parts that are commonly purchased with this part are the Brushes (part number 27847), Armature (27072), and the Power Cord (64250).

Installation Instructions

Marilyn from BROOKINGS, OR

No problem really, I had just realized that the carbon brushes should be replaced periodically.

I followed the instructions that came with the kit. Read more...

Compl. Armature Assy - Service

$71.24

Fix Number: FIX12006391
Manufacturer Part Number: 27072

This genuine manufacturer-sourced part is specially made for use with Andis clippers. The armature is the main portion of an electric motor which rotates the shaft. You'll need to replace the armature if you notice smoke or sparks coming from the vents on the back of your equipment. If this happens, you've probably overloaded your armature and some point, which caused the insulation to break down. It provides an identical replacement for a faulty or a missing component that was installed on a new unit. Check the owners manual and the diagrams of your specific model for the correct installation of this armature. Note, this high-quality part is sold individually.

Installation Instructions

petter from P C BEACH, FL

good

good Read more...

Andis Clipper Trimmer Parts

Popular Andis Clipper Trimmer Parts

Installation Instructions

Installation Instructions

Andis Clipper Trimmer Appliance Types

Related Andis Clipper Trimmer Parts

Popular Andis Clipper Trimmer Models

Andis Clipper Trimmer Parts

Start With Your Model Number

Popular Andis Clipper Trimmer Parts

Installation Instructions

Installation Instructions

Andis Clipper Trimmer Appliance Types

Related Andis Clipper Trimmer Parts

Popular Andis Clipper Trimmer Models