Andis Parts

Fix Number

FIX12164188

Manufacturer Part Number

201394

This part comes directly from Andis. This Tension Spring is used in multiple models of Andis hair trimmers. The Spring is made of metal and includes the nylon tip. The Spring holds tension on the cutter of the blade. If the blade doesn't move, then this part should be replaced. This part is commonly purchased with the Tension Screw (part number 32527) and the Retaining Screws (29752). Tools Used: • Flat Head Screw Drivers • Philips Head Screw Driver

Fix Number

FIX12006391

Manufacturer Part Number

27072

This genuine manufacturer-sourced part is specially made for use with Andis clippers. The armature is the main portion of an electric motor which rotates the shaft. You'll need to replace the armature if you notice smoke or sparks coming from the vents on the back of your equipment. If this happens, you've probably overloaded your armature and some point, which caused the insulation to break down. It provides an identical replacement for a faulty or a missing component that was installed on a new unit. Check the owners manual and the diagrams of your specific model for the correct installation of this armature. Note, this high-quality part is sold individually.

Fix Number

FIX17016561

Manufacturer Part Number

69136

This is an authentic replacement part manufactured for Andis clippers. This molded rubber switch button is the cover seen from the side of the clipper, when pressed the button engages the circuit board. Overtime the switch button can wear exposing the circuit board, it is recommended to replace worn switch buttons. The switch button is sold individually, and the circuit board is available separately.

Fix Number

FIX12006329

Manufacturer Part Number

22682

Fix Number

FIX12006469

Manufacturer Part Number

64250

This is a genuine manufacturer approved replacement power cord used with Andis clippers. If the cord is damaged it is important to replace it before continuing to use the tool. This cord is sold individually. Please note the cord protector/sleeve is included. To complete this repair you would need a screwdriver.

Fix Number

FIX12006211

Manufacturer Part Number

01767

This is a genuine high quality switch assembly that is sourced directly from original equipment manufacturer for use with Andis clippers. It is the part of the tool that allows user to turn the unit on and off. Over time mechanical switches will wear out and may begin to fail eventually requiring replacement. Replacing it is a simple task that should only require a screwdriver. One durable plastic switch with two lead wires attached is included per order.

Fix Number

FIX12006409

Manufacturer Part Number

28194

This part comes directly from Andis. The Hinge is used on multiple models of Andis hair clippers. The Hinge holds the blade into place allowing the Blade Drive to move the cutter on the blade back and forth. The Hinge should be replaced if it no longer has enough tension to secure the blade. To replace the Hinge two Philips Head Screws need to be removed. Once they are removed replacing the hinge will be simple. Tools used: • Philips Head Screwdriver

★★★★★

★★★★★

1 Review

Fix Number

FIX12006310

Manufacturer Part Number

21812

This is a genuine OEM sourced replacement carbon brush repair kit. It is specially manufactured for Andis clippers. Carbon brushes help to conduct electric current in an electric motor. Over time brushes tend to wear our requiring replacement. This repair kit includes includes (2) carbon brushes, (2) metal springs and (2) plastic brush caps. Please note, brush holders are sold separately. Replacing these brushes is a simple task that should only require a flat-head screwdriver. • First make sure to unplug the clippers • Remove the brush caps • Remove the old brushes • Install the new brushes • Reassemble and test the clippers

Fix Number

FIX12006404

Manufacturer Part Number

27847

This is a genuine OEM sourced replacement part designed for use with Andis clippers. This assembly includes one (1) carbon brush with a lead wire attached. Please note brush spring and retaining clip are both sold separately. Due to normal use and friction brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • First remove cover • Take our old brushes and replace them with the new ones • Secure the cover and test the tool

Fix Number

FIX12006571

Manufacturer Part Number

65806

It is a genuine item that is supplied by the original equipment manufacturer for Andis clippers. This part provides an identical replacement for a missing or a faulty spring that was installed on a new unit. The purpose of this spring is to apply tension to the brush, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality spring is made of durable metal and is sold individually.