Ice Funnel
$38.10
In Stock
Fix Number: FIX652226
Manufacturer #: WR17X11267
Manufactured by:
GE
-
Product Description
This paddle, when your glass is pushed against it, activates the dispenser to release the ice through the funnel.
-
Works with the following brandsGeneral Electric, Hotpoint
-
Works with the following productsRefrigerator
-
Fixes the following symptomsNot dispensing water, Ice maker won’t dispense ice
-
Part Number Cross ReferencePart# WR17X11267 replaces these:AP3192458, 947252, WR17X11267, WR17X10743, WR17X11277
Product Description
This paddle, when your glass is pushed against it, activates the dispenser to release the ice through the funnel.
-
Works with the following brands:General Electric, Hotpoint
-
Works with the following products:Refrigerator
-
Fixes the following symptoms:Not dispensing water, Ice maker won’t dispense ice
-
Part# WR17X11267 replaces these:AP3192458, 947252, WR17X11267, WR17X10743, WR17X11277
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related PartsAdditional or alternate parts to consider.
Installation Instructions Provided by Fix customers like you.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
-
Customer:Karen from Redlands, CA
-
Parts Used:WR17X11267
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Our ice funnel dispenser had cracked
We watched video for installation instructions. We had to use a flat head screwdriver to pry off the display panel instead of how the video instructed. This frig is 13 years old & made a little differently. We had some trouble getting the plastic wire connectors off the circuit board, & I broke one of the plastic clips on the board, but we finally were able to release the board and proceeded to remove the dispenser without any issues. I then cleaned the funnel opening and we removed the broken part and replaced it with the new funnel part without any other problems. We installed the new part and reconnected the circuit board to the plastic wire connectors, then snapped the display panel into place. We plugged in the frig and moved it back into place.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:PATRICIA from EGG HARBOR CITY, NJ
-
Parts Used:WR17X11267
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
ICE FUNNEL BROKE OFF
JUST FOLLOWED THE ON LINE VIDEO ON HOW TO REPLACE.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Wayne from New Tampa, FL
-
Parts Used:WR17X11267
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Changed the ice funel
Had to use very small screwdriver. I took out the front panel. I didn't unplug the pc board. Unscrewed the ice funel bracket and changed it out. Five minutes.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Eric from Fresno, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Replaced plastic bottom grill and ice funnel
On our GE Monogram refrigerator, which has brushed stainless-steel doors, I replaced the black plastic bottom grill under the water dispenser, and the ice funnel, because both of them were covered with hard water mineral deposits.The instructions here were correct, and I won't repeat them, except to emphasize that it's critical to put the funnel "finger" behind the electric actuator switch lever when you install it. The main reason I write is to explain how to deal with the fact that on the Monograms like ours, the steel freezer door covers the ice maker bezel. You actually have to remove the door skin to remove the bezel under it. That means unscrewing four screws on the top of the door, four screws under it, and maybe six more screws on the outside edge, accessible by opening the door and looking into the hinge area. With all of the screws out, you can use your fingers (wear gloves to prevent cuts) to gently flex the door skin off of the door, starting on the outside edge. It takes maybe five minutes to do. Set it somewhere safe, follow the other instructions on this site, then reinstall it, being careful to gently flex the metal skin over the water line at the bottom outside edge and a ground wire at the top. Put the screws back and you're done.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Betty from Bethel Park, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
No Ice Or Water from Dispenser
Replaced the dispenser housing & Ice Funnel that was damaged from trying to thaw the water supply to the dispenser with a hair dryer . Only problem is that the ice funnel is Black but the original was white , but it works fine
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
★
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Richard N - June 27, 2021
Verified Purchase
Repair complete.
Perfect replacement part.
- < Prev
- 1
- Next >
Model Compatibility
This part works with the following models:
Fix Number: FIX652226
Manufacturer Part Number: WR17X11267
Manufacturer Part Number: WR17X11267
Brand
Model Number
Description