Table Saw Wheels and Rollers

Popular Table Saw Wheels and Rollers

HANDWHEEL
$6.25
In Stock
★★★★★
★★★★★
4 Reviews
Fix Number
FIX18690189
Manufacturer Part Number
089290001054
This OEM approved replacement Handwheel is designed for use with specific models of Ridgid Table Saws. To ensure your saw is compatible with this part, please see the "Model Cross Reference List" below. The purpose of the handwheel is to raise and lower the saw blade. This Handwheel is made of durable black plastic, is approximately 4" tall, and is sold individually. If your Handwheel is visibly damaged or no longer properly moves the saw blade, it needs to be replaced. No tools are required for installation.
Handwheel
$24.40
In Stock
Fix Number
FIX10178360
Manufacturer Part Number
5140117-77
This is an OEM handwheel for a table saw, which allows the user to adjust the blade height. This handwheel is made from black plastic (bevel handle is sold as a separate part) and attaches to a metal cross pin on the spindle. The plastic will wear over time, causing it to slip and not adjust the blade. This is a simple repair that should only take a few minutes. Start by removing the nut, pull the handle away from the saw (being careful not to misplace the washer), and secure the new assembly by aligning the notches with the roll pin, and secure the new handwheel with the nut.
Extension Roller
$52.51
In Stock
Fix Number
FIX11878430
Manufacturer Part Number
44-96-0140
This is an authentic Milwaukee replacement part that has been sourced from the original manufacturer to be used with panel saws. The plastic extension roller is part of the frame assembly and is used to allow the guide tubes to move horizontally. This item is priced individually.
WHEEL
$29.28
Special Order
Fix Number
FIX18690284
Manufacturer Part Number
089290001176
The wheel attaches to the lower stand. It is a genuine OEM sourced part which is specially designed for use with Ridgid saws. This item is sold individually and is made of plastic and hard rubber. A wrench may be helpful when replacing this part. It might break over time and will need replacing.
Handwheel
$6.25
In Stock
Fix Number
FIX16668801
Manufacturer Part Number
3130253239
Shaft
$24.42
In Stock
Fix Number
FIX10177011
Manufacturer Part Number
5140032-18
This is a genuine DeWALT hardware which is sourced from the original manufacturer for use with table saws. It is an identical replacement for a missing or a damaged shaft that was installed on a new unit. Refer to the diagrams for your model to ensure the exact location and the correct application of this component. This high-quality part is made of durable metal and is sold as an individual item. You may need a screwdriver and pliers to perform this repair.
Hand Wheel
$6.15
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX10077069
Manufacturer Part Number
089037007041
This is an authentic replacement part sourced from original manufacturer. It is designed for use with Ryobi table saw. This is the hand wheel that allows you to adjust height/bevel of the table saw. It is made out of metal and it is sold individually. Please note the hand wheel cap/cover is sold separately. To complete this repair you would need a screwdriver and pliers.
Shaft Elevating W/spring Pin
$6.25
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX10077401
Manufacturer Part Number
089037011024
This is an authentic replacement part manufactured for use with Ryobi table saws. The shaft connects to the handwheel and is used to raise and lower the height of the blade. This elevating shaft is sold as an individual replacement part, please see model diagram for associative parts.
Shaft
$24.00
In Stock
Fix Number
FIX10177013
Manufacturer Part Number
5140032-20
This is an original replacement part manufactured for use with DeWalt table saws. This special shaft is used to lock the rip fence to prevent the fence from moving while making a cut. This shaft is just one component of the locking system, please see model diagram for additional parts. The shaft is available as an individual replacement part.
Elevating Shaft (3/8-16 X 137
$6.25
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX10077070
Manufacturer Part Number
089037007042
It is a genuine item that is supplied directly from the original equipment manufacturer for use with Ryobi table saws. This is an identical replacement for a missing or worn elevating shaft that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your unit for the correct location and application of this component. Keep in mind this high-quality item is made of durable metal and is sold individually.

Table Saw Wheel or Roller Brands