Table Saw Bearings

Fix Number

FIX19512517

Manufacturer Part Number

2610911928

This is a ball bearing, sold individually, and designed for table saws and miter saws. This ball bearing has shielding on both sides and is sold as an individual part. Ball bearings minimize friction produced by moving parts. This lessens the wear on the saw and allows it to run efficiently. Bearings are a common wear part due to the constant pressure, heat and vibration, so it is advised to inspect and replace them regularly. This part, like all the parts we sell, is sourced directly from the original manufacturer.

Fix Number

FIX10169630

Manufacturer Part Number

330003-60

This is a bearing, and it is used in various power tools. It is meant to reduce tension between the moving parts within the tool. This bearing has a 1 inch outer diameter, less than 1/4-inch inner diameter, and green walls.

Fix Number

FIX10463888

Manufacturer Part Number

BB-6203ZZ

This ball bearing is 17 mm and fits a variety of gardening power tools. The ball bearing has two contact rubber seals on each side and two non-contact metal shields on each end as well. Tip: if your tools needs only one seal or shield, then take off one of the shields or seals from this ball bearing. Refer to the manual provided by the manufacturer for further installation instructions and a detailed diagram.

Fix Number

FIX19510599

Manufacturer Part Number

2610004595

★★★★★

★★★★★

1 Review

Fix Number

FIX10169632

Manufacturer Part Number

330003-64

This is a ball bearing for your power tools. It is used in a variety of machines for rotary motion. The bearings support your tools by lowering the friction, which allows easy rotation of moving parts. Depending on how often you use your tool the bearings are a commonly replaced part. This is because they will experience most of the pressure, heat, and vibrations.

Fix Number

FIX10315390

Manufacturer Part Number

1086894S

This ball bearing fits a variety of lawn and gardening tools. The ball bearings prevent friction between rotating parts. The balls do this by bearing the load and spin and distributing the weight equally, while the minimal contact area of the balls reduce friction. This allows your tool to run easily. Ball bearings are a commonly replaced part because of the constant wear they experience. Tip: check your bearings and replace them periodically. *Please note: they are sold individually.

★★★★★

★★★★★

1 Review

Fix Number

FIX12021652

Manufacturer Part Number

422043030003S

This arbor and flange assembly is designed for right-tilt table saws and plays a key role in securing the saw blade for smooth, accurate, and safe cutting. Made from durable metal, it helps reduce vibration and restore proper blade alignment when the original arbor becomes worn or damaged. This assembly is typically sold without bearings and is commonly used during repairs or partial rebuilds. Be sure to confirm your saw’s configuration and compatibility before purchasing to ensure proper fit and performance.

Fix Number

FIX10463896

Manufacturer Part Number

BB-6205ZZ

This ball bearing fits a variety of power tools and works to protect rotating parts from wearing each other down. It can also protect damage coming from incorrect positions. Because of the constant friction it experiences, this a commonly replaced part. *Please note: this part is sold individually. For installation instructions refer to the diagram provided by the manufacturer.

Fix Number

FIX16237257

Manufacturer Part Number

089110101209

This replacement bearing is an authentic component which is supplied directly from the original equipment manufacturer for use with Ryobi table saws. Bearings are used to reduce friction between rotating parts, please make sure to check appropriate diagrams of your unit for the correct location and use of this hardware. Over time bearings tend to wear out and may begin to fail eventually requiring replacement to maintain peak performance. This part is made of high-quality metal and it is sold individually.

Fix Number

FIX10166797

Manufacturer Part Number

153451-00

This is available as an individual replacement part and is made of metal. The thrust bearing goes between two thrust washers and helps to reduce friction. If this part becomes broken it will need to be replaced and may require a socket set during the installation. This is an OEM DeWALT part directly sourced from the manufacturer for use in table saws and miter saws.