OEM Ryobi Miter Saw Parts & Accessories

Ball Bearing (6000lu)

$6.40

Fix Number: FIX9868401
Manufacturer Part Number: 039176001012

It is an original manufacturer supplied replacement item and is sold individually. This ball bearing is sealed on both sides. Ball bearings are made to reduce friction between two rotating parts. Because they experience constant pressure they would need to be checked and replaced periodically to ensure top performance. Please check diagrams for correct location and application of this bearing.

Brush

$6.51

Fix Number: FIX16235992
Manufacturer Part Number: 089006017092

Designed for use with select Ridgid and Ryobi tools, this OEM approved replacement Brush fits a variety of models. To see if this part will fit your tool, please see the "Model Cross Reference List" below. This brush is made out of a durable Carbon alloy, has a lead wire attached to it, and its primary purpose is to conduct electrical current from the stationary wires to the moving parts of your tool. Brushes are one of the most commonly replaced power tool parts because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common cause of intermittent motor function, reduced electric braking, and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. Brushes are sold individually, and might also be known as Carbon Brushes or Motor Brushes. It is recommended to replace both brushes, even if only one is worn.

Installation Instructions

rich from WILLOW GROVE, PA

blade was making bad noise, and not spinning properly

Removed motor housing, arm, handle, spring and replaced. Found that gear and pinion were both stripped. Poor quality metal used in both. Read more...

Brush Cap

$6.51

Fix Number: FIX16235993
Manufacturer Part Number: 089006017093

This Brush Cap is an authentic OEM part for Ryobi and Ridgid Saws. The purpose of the brush cap is to keep the brush and brush holder securely inside the tool. The brush cap is made of a high-quality black plastic and is sold individually. A flathead screwdriver can be used when installing this part.

Installation Instructions

rich from WILLOW GROVE, PA

blade was making bad noise, and not spinning properly

Removed motor housing, arm, handle, spring and replaced. Found that gear and pinion were both stripped. Poor quality metal used in both. Read more...

Handle Assembly

$22.40

Fix Number: FIX16238314
Manufacturer Part Number: 089240031708

Brush Assembly

$12.91

Fix Number: FIX16235785
Manufacturer Part Number: 080016005121

Throat Plate

$6.51

Fix Number: FIX11855822
Manufacturer Part Number: 089041009004

This is an authentic Ryobi replacement part that is OEM sourced to be used with miter saws. The durable plastic throat plate attaches to the saw's table and is used support the material being cut near the blade of the saw to aid in making cleaner cuts. A screwdriver is needed to install this item and it is sold individually.

Chute, Dust A

$6.51

Fix Number: FIX16237632
Manufacturer Part Number: 089240011018

Fence

$80.07

★★★★★

2 Reviews

Fix Number: FIX11855823
Manufacturer Part Number: 089041009005

This is an authentic Ryobi replacement part, sourced from the original manufacturer for use with miter saws. The fence assembly connects to the table and is used to provide a surface to rest material against. This item is available as an individual replacement part.

Ball Bearing (6203zz)

$6.51

★★★★★

1 Review

Fix Number: FIX9871915
Manufacturer Part Number: 089210136012

This is a genuine replacement part sourced from the original manufacturer for use with edgers, sanders, and miter saws. The special ball bearing is commonly used to reduce friction between a rotating shaft and fixed part assembly. This ball bearing is available as an individual replacement please see model diagram for associative parts.

Bearing Ball 608zz

$6.40

Fix Number: FIX11858686
Manufacturer Part Number: 680141022

Genuine Manufacturer Approved replacement part used on a variety of Power Tools. This Ball Bearing has multiple applications depending on your tool. This part is made out of Metal and it is Sold Individually. Ball Bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement. To replace this Bearing you would need a Screwdriver and a Set of Wrenches.

Ryobi Miter Saw Parts

Popular Ryobi Miter Saw Parts

Installation Instructions

Installation Instructions

Ryobi Miter Saw Appliance Types

Related Ryobi Miter Saw Parts

Popular Ryobi Miter Saw Models

Ryobi Miter Saw Parts

Start With Your Model Number

Popular Ryobi Miter Saw Parts

Installation Instructions

Installation Instructions

Ryobi Miter Saw Appliance Types

Related Ryobi Miter Saw Parts

Popular Ryobi Miter Saw Models