OEM DeWALT Miter Saw Parts & Accessories

Brush Box Asm

$6.51

Fix Number: FIX12522639
Manufacturer Part Number: N292059

This is a brush box assembly designed for various sander models. Brush boxes are essential components that house carbon brushes responsible for transferring electricity from the motor to the sanding pad. When the carbon brush assembly wears out, it can no longer efficiently transfer electricity, causing the sander to stop working. This brush box assembly includes the carbon brush, its housing, and the necessary wiring. Replacing the brush box assembly is a straightforward process, requiring only a screwdriver and a set of pliers. Begin by disconnecting your sander from its power source, whether it is a battery or a wall outlet. Next, remove the screws securing the main housing of the sander and locate the brushes inside. Use a set of pliers to disconnect the wire from the old brush and a flat-head screwdriver to lift the old brush out of its slot. Insert the new brush box assembly into the slot and connect its wires. Finally, reattach the sander outer housing and secure it with the screws.

Watch the install video

Miter Saw Kerf Plate

$18.01

Fix Number: FIX10166116
Manufacturer Part Number: 146726-02

This Kerf plate is a genuine DeWalt replacement part. It is made of plastic with a slot in the middle for the saw blade to slide through. It has 3 screw holes on each side (6 in total) to firmly secure the kerf plate to your saw. rnrnKerf plates (also called kerf boards) are used to prevent excessive splintering, resulting in cleaner cuts. Using the wrong kerf plate for your tool can give a rough edge to the material you’re cutting.

Watch the install video

Brush

$21.48

Fix Number: FIX10170261
Manufacturer Part Number: 381028-08

This carbon brush fits a variety of gardening and lawn tools. The brush is a common replacement part and can easily fix most motor malfunctions. This brush comes with a wire lead and a connection terminal. Inspect the wire lead for any damage and replace immediately if burns or cracks are noticed. Refer to the diagram provided by the manufacturer for installation instructions.

Wear Plate

$32.75

Fix Number: FIX10181974
Manufacturer Part Number: 618192-00

This is a genuine manufacturer sourced replacement part designed for use with Dewalt miter saws. This wear plate helps to minimize the friction and avoid potential wear to the table assembly. It is made out of plastic and it is sold individually.

Watch the install video

Switch

$51.29

★★★★★

1 Review

Fix Number: FIX10181008
Manufacturer Part Number: 606056-00

This is a trigger switch, which controls the on and off and variable speed functions of the power tool. This trigger has four terminals, which will damage and wear with use. If your equipment is not starting when using the switch or if the variable speed or electric braking are not functioning, these are all common symptoms of a malfunctioning trigger switch. This part is genuinely sourced direct from the manufacturer and is sold individually.

Watch the install video

Blade Adapter Ring

$7.19

★★★★★

2 Reviews

Fix Number: FIX10166690
Manufacturer Part Number: 152636-00

This is an authentic adapter ring used to mount the saw blade to your miter saw. It is sold as an individual part. Standard 12-inch saw blades have a 1-inch arbor hole, while most miter saw arbors are 5/8 of an inch. This adapter ring is placed on the blade hole and over the arbor so you can use a 12-inch blade. This part is prone to wear and tear, which will make the blade unbalanced, signalling that it should get replaced.

Bolt Assy

$6.51

Fix Number: FIX12530513
Manufacturer Part Number: N436564

This is a genuine Dewalt replacement part, it is sold individually. The purpose of this bolt is to secure the blade on the miter saw models shown below. It has a 1/2 " hex head. It is 1 inch long, with left hand threads.

Miter Saw Ball Bearing

$18.72

★★★★★

1 Review

Fix Number: FIX10188573
Manufacturer Part Number: N127530

This Ball Bearing is sealed on both sides. It is a genuine replacement part and is sold individually. Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

Fixes these symptoms

Grinding or squealing sound
See more...

Watch the install video

Power Cord

$40.44

Fix Number: FIX10169913
Manufacturer Part Number: 330079-98

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

Carbon Brush

$11.02

Fix Number: FIX10181643
Manufacturer Part Number: 614367-00

This OEM brush is sold individually, however two are needed in most power tools, and should be replaced at the same time, even if only one is worn. If the motor of your power tool is running poorly, worn brushes are the likely cause. A brush that is worn out will often wear down near the wire lead and can become cracked, pitted, or burned. When replacing the carbon brushes, take this time to check the condition of the armature, if it appears damaged this can indicate more significant motor issues.

DeWALT Miter Saw Parts

Popular DeWALT Miter Saw Parts

DeWALT Miter Saw Appliance Types

Related DeWALT Miter Saw Parts

Popular DeWALT Miter Saw Models

DeWALT Miter Saw Parts

Start With Your Model Number

Popular DeWALT Miter Saw Parts

DeWALT Miter Saw Appliance Types

Related DeWALT Miter Saw Parts

Popular DeWALT Miter Saw Models