Jet Band Saw Parts

Jet Appliance Parts

Popular Jet Band Saw Parts

Wheel Protector
$49.40
In Stock
Fix Number
FIX10516474
Manufacturer Part Number
5782691
This is an authentic replacement wheel tire for Wilton and Jet band saws. It is supplied directly from original equipment manufacturer and it is sold individually. Its purpose is to provide a stable grip for the saw blade. When attaching the new tire on a band saw wheel, it may appear too be too small, however it really is not. These tires when new are typically approximately two (2) or more inches shorter than the old tire. Tires are supposed to fit very tightly against the bad saw wheel. As the tire ages, the rubber hardens allowing for the blade to slip. Note, it is a good idea to put the new tire in hot/warm water to heat it up just enough to make it pliable enough to stretch. Its advised to have two people in the stretching process.
Ball Bearing
$30.18
In Stock
Fix Number
FIX10463892
Manufacturer Part Number
BB-6204ZZ
This is an authentic OEM replacement part used for various handheld power tools including models by Powermatic, Jet, and Wilton. Bearings stabilize and buffer moving parts to facilitate rotation of such parts as shafts, axles, and gears. They are commonly replaced due to this high wear function. This part sold individually.
Table Insert
$19.60
On Order
Fix Number
FIX10516515
Manufacturer Part Number
5783471
This item is a genuine part that has been sourced from the original manufacturer to be used with verticle bandsaws from Wilton and Jet. The durable plastic insert fits into the cap in the table where the blade passes through the table. The insert is used to reduce the gap around the blade in order to better support the material as it is being cut. Inserts wear down from normal use, and will eventually need to be replaced to maintain clean accurate cuts. This part is priced as a single item, please note tools may not be necessary to install the insert.
Ball Bearing
$41.16
In Stock
Fix Number
FIX10463882
Manufacturer Part Number
BB-6201VV
This replacement part is supplied by the original equipment manufacturer for use with Powermatic and Jet power equipment. Ball bearings are generally used to reduce friction between rotating parts, please make sure to check appropriate diagram of your model for the correct location and use of this hardware. Over time the rollers may begin to wear out restricting the movement and eventually requiring a replacement to maintain peak performance. This high-quality part is made of durable metal and it is sold individually.
Flat Washer, M8
$10.54
In Stock
Fix Number
FIX10517157
Manufacturer Part Number
TS-1550061
This flat washer is designed to fit a variety of power tools. The washer helps distribute the pressure evenly between parts and has multiple applications depending on your specific tool. Check the diagram for the accurate location in your tool. *Please note: this part is sold individually.
Ball Bearing
$45.28
In Stock
Fix Number
FIX10463888
Manufacturer Part Number
BB-6203ZZ
This ball bearing is 17 mm and fits a variety of gardening power tools. The ball bearing has two contact rubber seals on each side and two non-contact metal shields on each end as well. Tip: if your tools needs only one seal or shield, then take off one of the shields or seals from this ball bearing. Refer to the manual provided by the manufacturer for further installation instructions and a detailed diagram.

Installation Instructions

Adam from FREMONT, NE
Saw was making loud screeching noise and unsatisfactory cuts
1: disconnect power and remove blade
2: remove spanner nut
3: remove arbor nut. Spins opposite:
righty loosy lefty tighty
4: remove arbor with mallet and dowel
5: use arbor press to take off ball bearing
6: press on new bearing
Read more...
Blade Guide-carbide
$49.40
In Stock
Fix Number
FIX10516511
Manufacturer Part Number
5783391
This part is an OEM from the Wilton manufacturer. The carbine blade guard is compatible with many band saw devices. The plastic item is fitted on each side of the saw head's support bracket, keeping the blade straight for cutting projects. A pair of pliers and a screwdriver may be helpful for making the repair. The carbine blade guard is sold individually.
Ball Bearing
$73.24
In Stock
Fix Number
FIX10463890
Manufacturer Part Number
BB-6204VV
This is a genuine Powermatic and Jet part sourced directly from the manufacturer for use in planers, saws, and jointers. The ball bearing fits between the gear and the oil seal. A screwdriver may be necessary during the installation of this item. It may become broken or wear down and will need to be replaced. This is available as an individual replacement part and is made of metal.
Pad
$10.54
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX10465206
Manufacturer Part Number
JWBS18-434
This pad is an OEM part direct from Powermatic. Constructed of soft material, this item is compatible with several band saw devices. The pad is fitted onto the fence, providing protection from abrasion. The pad is sold individually. No tools are required for the replacement.
Ball Bearing
$49.40
In Stock
Fix Number
FIX10463886
Manufacturer Part Number
BB-6202ZZ
This is an authentic OEM replacement part for certain models of Jet, Powermatic, and Wilton tools that is sourced from the manufacturer. To ensure that this will fit your tool, please see the "Model Cross Reference List" below. This part has an outer diameter of 1.5", and metal shielding on both sides. The bearing is used to reduce friction between two rotating parts. It keeps wear on the equipment to a minimum, and helps the mechanics run efficiently. Depending on how often you use your tool, your bearings will need routine replacement due to continual pressure on them. Signs of broken or failing Ball Bearings include squealing, screeching, or grinding noise when powering the device off. Each is sold individually.

Jet Band Saw Appliance Types

Related Jet Band Saw Parts

Popular Jet Band Saw Models