Laminate Trimmer Parts

Power Cord

$17.56

Fix Number: FIX10169875
Manufacturer Part Number: 330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Ball Bearing

$4.99

★★★★★

1 Review

Fix Number: FIX10180918
Manufacturer Part Number: 605040-65

If your tool is making a squeaking or squealing sound, a worn bearing is a likely cause. Bearings are designed to lessen the friction between moving parts, so they are prone to deterioration over the life of your equipment. This part includes one OEM ball bearing which is sealed on both sides. Installation may vary depending on the model-type, but in general, this should be a quick and easy repair that can be easily done yourself.

Watch the install video

Power Cord

$21.97

Fix Number: FIX10153834
Manufacturer Part Number: 664064-4

This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing your old cord, take note of the wire leads placements, and how they connect to the receptacle in the tool. You will have to attach the new cord similarly.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Bearing

$4.99

Fix Number: FIX10188435
Manufacturer Part Number: N110359

This authentic ball bearing is sold individually. It can be used in a variety of differently model types, such as miter saws, circular saws, table saws, and angle grinders. This ball bearing is sealed on both sides. Its job is to minimize friction between rotating parts. The armature rotates at a very fast rate, so after years of use, it is normal for the bearings to wear.

Watch the install video

Carbon Brush Set CB-408 6x9mm

$10.85

Fix Number: FIX10156657
Manufacturer Part Number: CB408

This part includes two carbon brushes with wire leads and brush springs. Worn brushes are typically presented as a failed or underperforming motor. Carbon brushes are a part that commonly wears, so it is a good idea to have these on hand. They are essential for a properly running motor because they conduct electricity to the armature. For this repair, you will start by removing the first brush from the motor, using a screwdriver to remove the brush cap. Once the cap is removed, the brush can be removed. Align the new brush with the holder and then reinstall the cap. Repeat these same steps for the other brush.

Watch the install video

Carbon Brush Set CB-75

$7.83

Fix Number: FIX10156669
Manufacturer Part Number: CB75

If your motor is running poorly, running intermittently, it is likely in need of new carbon brushes. This part includes a set of two carbon brushes with wire leads and brush springs attached. Changing the carbon brushes is part of your regular maintenance, so it is a good idea to have a few extra on hand. When replacing the carbon brushes, it is also advised to inspect the armature at the same time.

Strain Reliever

$7.69

Fix Number: FIX10113583
Manufacturer Part Number: 901266

This is a strain reliever for your power tools. It found at the meeting place between your cord, and the outer tool housing. The relief is an important part for your power tool because it protects your cord from tearing and breaking due to constant pressure. Keep your relief in good condition because it will extend the life of the cord, and the machine overall.

Installation Instructions

Jeff from WISC RAPIDS, WI

Strain reliever broken at base of saw. Core frayed.

1. Unplug saw. 2.Examine and determine which parts need to be removed to gain access to switch. 3.Remove screws one at a time and placed in dish keeping track of size and length of where removed from handle. 4. Slowly pull handle apart exposing switch and wires. 5. Remove screws holding black and white wires keeping track of which wire goes where. 6. Thread new power cord the same way the old one was positioned though the handle and reassemble. Read more...

Brush Assembly

$8.51

Fix Number: FIX10116512
Manufacturer Part Number: N031636

This OEM part includes one carbon brush in metal housing. A worn or damaged brush will lead to motor issues and should ideally be replaced before this happens. It is a good idea to continue to inspect the brushes and replace as soon as they appear tarnished in any way. This is also an opportune time to inspect the armature for burns or cracks.

Watch the install video