OEM Makita Planer Jointer Parts & Accessories

Carbon Brush Set

$10.85

Fix Number: FIX10156641
Manufacturer Part Number: CB154

This motor brush set is for power tools. Motor brush set transfers electric current to the spinning armature in the motor. The set includes both motor brushes.

Watch the install video

Power Cord

$21.97

Fix Number: FIX10153834
Manufacturer Part Number: 664064-4

This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing your old cord, take note of the wire leads placements, and how they connect to the receptacle in the tool. You will have to attach the new cord similarly.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Carbon Brush CB-124 (Set of 2)

$7.83

★★★★★

1 Review

Fix Number: FIX10156640
Manufacturer Part Number: CB124

Carbon brushes are needed to conduct electricity to the armature through the commutator. The brushes are continuously rubbing against the rotating commutator, so will wear down over time, and will need to be replaced. If you are experiencing excessive sparks, this can also be caused by a damaged armature, so it is best to check it at the same time. This part includes two carbon brushes, which need to be replaced at the same time.

Power Cord - 8', 14 Gauge, 2-Wire

$29.38

Fix Number: FIX10153852
Manufacturer Part Number: 664463-0

This power cord includes 2 prongs, 2 wires, and the gauge is 14. The measurement is 8 feet long and the type is bare wire. The cord is used on various power tools, specifically gardening and lawn equipment. With use and time, power tool cords can become frayed. If there are visible signs of wear on your cord, it is important to replace it immediately. For safety practices and installation instructions, refer to the diagram provided by the manufacturer.

Watch the install video

Carbon Brush Set CB-408 6x9mm

$10.85

Fix Number: FIX10156657
Manufacturer Part Number: CB408

This part includes two carbon brushes with wire leads and brush springs. Worn brushes are typically presented as a failed or underperforming motor. Carbon brushes are a part that commonly wears, so it is a good idea to have these on hand. They are essential for a properly running motor because they conduct electricity to the armature. For this repair, you will start by removing the first brush from the motor, using a screwdriver to remove the brush cap. Once the cap is removed, the brush can be removed. Align the new brush with the holder and then reinstall the cap. Repeat these same steps for the other brush.

Watch the install video

Pin Cap

$4.99

Fix Number: FIX10150565
Manufacturer Part Number: 417771-6

Watch the install video

Carbon Brush Set CB-75

$7.83

Fix Number: FIX10156669
Manufacturer Part Number: CB75

If your motor is running poorly, running intermittently, it is likely in need of new carbon brushes. This part includes a set of two carbon brushes with wire leads and brush springs attached. Changing the carbon brushes is part of your regular maintenance, so it is a good idea to have a few extra on hand. When replacing the carbon brushes, it is also advised to inspect the armature at the same time.

Watch the install video

Switch Button

$4.99

Fix Number: FIX10150875
Manufacturer Part Number: 419566-3

This is an individually sold black switch button. The switch button is what the user presses to turn the tool on or off. It connects to the actuating lever which runs to the switch. Due to consistent use , the switch can be prone to deterioration. If the tool is not turning on, or the locked position is no longer working, it may be due to a malfunctioning switch. This OEM quality switch is the part you will need to get your tool up and running again.

Cord Guard / Strain Reliever

$3.99

★★★★★

1 Review

Fix Number: FIX10153921
Manufacturer Part Number: 682505-8

This cord guard or strain reliever prevents cord damage by covering the last portion of a cord before entering a tool. This provides extra support and rigidness. The cord fits garden and lawn equipment. With use, the cord guard can break down and your cord is left unprotected, in this case it is best to replace the guard. Refer to the diagram provided by the manufacturer for installation instructions.

Carbon Brush Set CB-203

$13.88

Fix Number: FIX10156645
Manufacturer Part Number: CB203

This part includes two carbon brushes with the wire leads and brush springs attached. In order for your motor to run at peak performance, it is imperative that the carbon brushes are well-maintained. The carbon brushes are needed to conduct electricity to the armature through the commutator. Over time these brushes wear down due to the constant rubbing. They should be regularly inspected to ensure your equipment continues to run smoothly. This repair should only take a few minutes.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Makita Planer Jointer Parts

Popular Makita Planer Jointer Parts

Installation Instructions

Installation Instructions

Appliance Type

Popular Makita Planer Jointer Models

Makita Planer Jointer Parts

Start With Your Model Number

Popular Makita Planer Jointer Parts

Installation Instructions

Installation Instructions

Appliance Type

Popular Makita Planer Jointer Models