Max Nailer Seals and Gaskets

Fix Number

FIX10413750

Manufacturer Part Number

KN12628

This is an authentic replacement part manufactured for use with Max pneumatic stick nailers. The cylinder seal is used to seal the connection between the top of the cylinder and the cylinder valve. This cylinder seal is available as an individual replacement part, please see model diagram for associative parts.

Fix Number

FIX10412960

Manufacturer Part Number

HH11138

This authentic OEM part has been sourced directly from Max. This replacement o-ring is used on the trigger valve assembly. Be sure to properly lubricate o-rings before you place parts back inside the nail gun. This o-ring is made of rubber so it will wear down over time and need to be replaced. This 1Ap20 o-ring is sold individually.

Fix Number

FIX10412533

Manufacturer Part Number

CN37824

This is an authentic manufacturer-sourced replacement cylinder seal which is specially made for use with Max nailers and staplers. The purpose of this item is to provide a tight seal between connected components, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable rubber material and is sold individually.

Fix Number

FIX10412435

Manufacturer Part Number

CN36308

It is an authentic item that is supplied directly from the original equipment manufacturer for Max nailers. The purpose of this component is to provide an air-tight seal for the cylinder cap, unfortunately, over time the material will wear out and it may begin to crack eventually requiring a replacement. Make sure to check the appropriate diagram of your model for the exact location and application of this part. Keep in mind the seal is made of durable composite materials and is sold individually.

Fix Number

FIX10413054

Manufacturer Part Number

HH19196

It is an OEM supplied item that is made for Max nailers. This is the special O-ring that provides a tight seal for the piston. Unfortunately, over time it can wear out and it may begin to crack eventually requiring a replacement. A worn piston O-ring can cause low compression resulting in poor performance. Check the appropriate diagrams for your model to ensure the correct repair procedure. Keep in mind this high-quality O-ring is made of durable material and is sold as an individual item. A screwdriver will be needed to take apart and reassemble the housing when replacing this component.

Fix Number

FIX10412559

Manufacturer Part Number

CN38006

This is an authentic manufacturer-sourced replacement o-ring which is specially designed for use with Max roof coil nailers. It helps to provide an air-tight seal for the cylinder, please refer to the appropriate diagrams of your model for the correct location and application of this hardware. It is made of high-quality rubber material and is sold individually.

★★★★★

★★★★★

1 Review

Fix Number

FIX10413808

Manufacturer Part Number

KN70142

This is an authentic Max replacement part. The cylinder cap seal is placed between the cylinder cap unit and the fame of the nail gun. This seal helps maintain pressure inside the nail gun while also helping to keep dust, dirt, and jobsite debris out. When this seal starts to wear down it will fail, air will begin to leak from your nail gun and it will no longer be able to drive nails effectively. This cylinder cap seal is sold individually.

Fix Number

FIX10412236

Manufacturer Part Number

CN34994

It is an authentic manufacturer-sourced replacement part which is specially designed for use with Max nailers. The purpose of this part is to provide an air-tight seal between components, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable rubber and is sold individually.

Fix Number

FIX10412287

Manufacturer Part Number

CN35286

This is an authentic Max component which is supplied by the original manufacturer for use with handheld nailers. The part is utilized to provide a tight seal for the cylinder cap. Unfortunately, over time it may wear out, get compressed and begin to crack eventually requiring a replacement. To ensure the proper repair procedure, check the appropriate diagrams for your model. Keep in mind it is made of durable material and is sold as an individual item. A screwdriver will be needed to replace this cylinder cap seal.

Fix Number

FIX10412977

Manufacturer Part Number

HH11170

It is a genuine manufacturer-sourced replacement part which is supplied for use with Max nailers and staplers. This is the o-ring which provides an air-tight seal for the head valve, please make sure to refer to the appropriate diagrams of your model for the correct location and use of this item. It is a high-quality component which is made of durable rubber and it is sold individually, over time the material may wear our and begin to crack eventually requiring replacement.