OEM Ridgid Pipe Tools Parts & Accessories

Carbon Brush Set

$27.40

Fix Number: FIX10097316
Manufacturer Part Number: 44815

Genuine Ridgid replacement part Set of 2 Carbon Brushes with wire lead and brush spring attached. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Bearing

$27.21

Fix Number: FIX10097309
Manufacturer Part Number: 44760

This is an authentic part assembled by original manufacturer. It can be found in Ridgid power tools including drum machines and threading machines. Ball bearings buffer moving parts in order to reduce friction and secure rotational positioning. Bearings are commonly replaced due to their high wear functions. Sold separately.

Power Cord Retainer

$8.04

Fix Number: FIX10097508
Manufacturer Part Number: 46730

Brush Cap Set

$12.28

Fix Number: FIX10097420
Manufacturer Part Number: 45660

This is an authentic manufacturer approved replacement brush caps. They are specially designed for Ridgid power drives. Brush caps are used to secure the brush in the tool. These caps have external threads that to screw into the opening on the housing of the tool. Be careful when removing and replacing these, they have a tendency to break. This item is made out of plastic and it is sold individually. You would need a flathead screwdriver to install or remove these caps.

Brush Assembly Set

$42.23

Fix Number: FIX10097280
Manufacturer Part Number: 44540

This is a genuine manufacturer sourced replacement part used on Ridgid pipe and bolt threading machine. It includes two (2) carbon brushes with lead wires attached and two springs. lease note brush holder is sold separately. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. It is recommended to replace both brushes at the same time. You would need a screwdriver to complete this job.

Power Cord (8-foot)

$80.79

Fix Number: FIX10103727
Manufacturer Part Number: 89155

This is a genuine service cord made for Ridgid power driver/cutting tools. It is supplied directly from original equipment manufacturer and it is sold individually. If the cord is damaged it is important to replace it before continuing to use the tool. Please note, the cord protector/sleeve is not included with this service cord, it is sold separately. To complete this repair you would need a screwdriver. • Remove the housing • Disconnect wires • Remove old cord • Secure the new one in place • Reconnect wires • Reassemble and test the tool

Switch Insulator

$19.01

Fix Number: FIX10097125
Manufacturer Part Number: 43390

Switch

$151.71

Fix Number: FIX10097329
Manufacturer Part Number: 44905

This is a genuine OEM sourced replacement part designed for use with Ridgid portable power drive. Switches are a commonly replaced part in power tools, handling on/off operations. Because switches use mechanical internals, they will degrade and wear out over time, eventually requiring replacement. This switch has a plastic body and it is sold individually. To replace this switch you would need a Screwdriver.

Shoulder Bolt

$10.45

Fix Number: FIX10097462
Manufacturer Part Number: 46210

This replacement shoulder bolt is supplied from original equipment manufacturer for use with Ridgid pipe and bolt threading machines. It is used to secure the lever arm assembly to the carriage unit. It is a hex head bolt and it is sold individually. You would need a wrench to install it.

Spring Kit

$21.87

Fix Number: FIX10095364
Manufacturer Part Number: 30983

These springs are OEM Ridgid parts directly sourced from the manufacturer for use in plastic pipe cutters. This kit contains four different springs that attach to various parts of the cutter including the blade, the upper handle, the drive pawl, and the pawl catch. They are made out of metal and during replacement may require a screwdriver to help install the springs correctly.

Ridgid Pipe Tools Parts

Popular Ridgid Pipe Tools Parts

Ridgid Pipe Tools Appliance Types

Related Ridgid Pipe Tools Parts

Popular Ridgid Pipe Tools Models

Ridgid Pipe Tools Parts

Start With Your Model Number

Popular Ridgid Pipe Tools Parts

Ridgid Pipe Tools Appliance Types

Related Ridgid Pipe Tools Parts

Popular Ridgid Pipe Tools Models