Pipe Tools Parts

Cutter Head Assembly

$61.62

Fix Number: FIX12091633
Manufacturer Part Number: 43-64-0287

The cutter head is a genuine OEM sourced part which is specially designed for use with Milwaukee nibblers and shears. A screwdriver may be helpful when replacing this item. It is made of metal and will need to be replaced if it breaks. This is available as an individual replacement part but includes the screws.

Brush Assembly Set

$42.23

Fix Number: FIX10097280
Manufacturer Part Number: 44540

This is a genuine manufacturer sourced replacement part used on Ridgid pipe and bolt threading machine. It includes two (2) carbon brushes with lead wires attached and two springs. lease note brush holder is sold separately. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. It is recommended to replace both brushes at the same time. You would need a screwdriver to complete this job.

Carriage Spring

$6.51

Fix Number: FIX10127842
Manufacturer Part Number: 40-50-0580

This is an authentic OEM part. The Milwaukee carriage spring is compatible with copper tubing cutters. The spring is fitted in the gearcase housing, providing the necessary tension. This metal item is sold individually. A hex key and a pair of pliers are helpful with the removal and replacement.

Axle

$6.51

Fix Number: FIX10128342
Manufacturer Part Number: 42-12-0210

Cutting Spring

$6.51

Fix Number: FIX10127843
Manufacturer Part Number: 40-50-0585

It is an authentic item that is made for use with Milwaukee copper tubing cutters. This component is supplied directly from the original equipment manufacturer. The spring is secured to the wheel axle and it applies tension on the cutting wheel. Over time it may wear out, lose tension or even break eventually requiring a replacement. One durable metal cutting spring is included. Make sure to refer to the appropriate diagrams and the owners manual of your model to ensure the correct replacement of this component. It is a simple repair that should not require any special tools.

Power Cord Retainer

$8.04

Fix Number: FIX10097508
Manufacturer Part Number: 46730

Carbon Brush Set

$27.40

Fix Number: FIX10097316
Manufacturer Part Number: 44815

Genuine Ridgid replacement part Set of 2 Carbon Brushes with wire lead and brush spring attached. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Brush Cap Set

$12.28

Fix Number: FIX10097420
Manufacturer Part Number: 45660

This is an authentic manufacturer approved replacement brush caps. They are specially designed for Ridgid power drives. Brush caps are used to secure the brush in the tool. These caps have external threads that to screw into the opening on the housing of the tool. Be careful when removing and replacing these, they have a tendency to break. This item is made out of plastic and it is sold individually. You would need a flathead screwdriver to install or remove these caps.

Compression Spring 3

$6.51

Fix Number: FIX10143081
Manufacturer Part Number: 231403-9

This is an authentic OEM part. The Makita compression spring 3 is constructed of metal, and is compatible with the HK1810 Scraper. This part is secured between the steel ball and tool holder, helping the device to hold specific scraping tools. This part is sold individually. A wrench is helpful in the removal and replacement.

Power Cord (8-foot)

$80.79

Fix Number: FIX10103727
Manufacturer Part Number: 89155

This is a genuine service cord made for Ridgid power driver/cutting tools. It is supplied directly from original equipment manufacturer and it is sold individually. If the cord is damaged it is important to replace it before continuing to use the tool. Please note, the cord protector/sleeve is not included with this service cord, it is sold separately. To complete this repair you would need a screwdriver. • Remove the housing • Disconnect wires • Remove old cord • Secure the new one in place • Reconnect wires • Reassemble and test the tool

Popular Pipe Tools Parts

Pipe Tools Brands

Related Pipe Tools Parts

Popular Pipe Tools Models

Pipe Tools Parts

Start With Your Model Number

Popular Pipe Tools Parts

Pipe Tools Brands

Related Pipe Tools Parts

Popular Pipe Tools Models