OEM Black and Decker Nibbler & Shears Parts & Accessories

Charger

$24.23

Fix Number: FIX17016372
Manufacturer Part Number: 90593303-01

This is a genuine Black and Decker replacement charger, sold individually. It’s designed to recharge the battery used in the cordless tools listed below. Over time, chargers can wear out or stop functioning properly. Replacing the charger is a cost-effective solution that can extend the life of your tools—often much less expensive than purchasing a brand-new unit.

Insert

$9.16

Fix Number: FIX10185704
Manufacturer Part Number: 91966-00

This is a genuine replacement part manufactured for use with powered shears. This insert is used as a nut to fasten the housing and is used with the screw part number 679889-00. The insert is sold individually and the screw is available separately.

Insert

$11.51

Fix Number: FIX10177395
Manufacturer Part Number: 5140037-07

This part is an OEM sourced directly from the manufacturer for use in shears made by DeWALT, Porter Cable, and Black & Decker. The Insert is made out of metal and attaches to the housing. It might require a screwdriver to replace this part if it becomes stripped or broken. This item is available as an individual replacement.

Right Knife

$56.12

Fix Number: FIX10185705
Manufacturer Part Number: 91967-00

This is a genuine replacement part that has been sourced from the original manufacturer to be used with shears from DeWalt, Porter Cable, and Black & Decker. The metal knife attaches to the front housing and is used to cut through material on the right side of the center knife. This item is sold as an individual replacement part.

Terminal

$6.51

Fix Number: FIX10173813
Manufacturer Part Number: 464228-00

This is a terminal for your power tools. The terminal attaches to the cord of your machine, and then to the electrical connection on the tool. Through this connection, the electricity travels from the wall, through the terminal, and into your machine. The most common reason for needing to replace this part, is if your machine is plugged in but not turning on.

Installation Instructions

John from SPRINGVILLE, CA

Old worn cord shorting out.

Remove the four screws and carefully separate the casing at the trigger handle. Disconnect the terminals by lifting the switch slightly, just enough to remove the inside terminal. Needle nose pliers will make it easier to remove the terminals. Slip the cord protector over the new cord. Cut the two new wires to the proper length. I measured the old connectors for proper fit. Strip a half inch off the insulation, carefully crimp and solder the wires to each terminal, reconnect the terminals, reposition the cord protector, align and snap the casing back together, and replace the four screws. Plug it in and test for proper operation. Read more...

Spacer

$9.16

Fix Number: FIX10185706
Manufacturer Part Number: 91968-00

The spacer goes between the blade and the knife and is made of metal. This part is an OEM from DeWALT, Porter Cable, and Black & Decker for use in shears. This item is available as an individual replacement part. You may need a set of pliers when replacing this item. Over time this part may break and will need to be replaced.

Shrubber Blade

$22.98

Fix Number: FIX11928771
Manufacturer Part Number: 90588614-02

This is an authentic replacement part manufactured for use with Black & Decker shrub trimmers. The shrubber blade is a complete attachment that is ready to install. This shrubber blade is sold as an individual replacement part, please see model diagram for associative parts.

Spacer

$14.11

Fix Number: FIX10185707
Manufacturer Part Number: 91968-01

This is an authentic DeWALT replacement part. The spacer is found in power shears, and is generally used to maintain separation between the left knife and the center knife. Please be aware that there are different spacers used in the machine. Refer to the parts diagram to be sure of ordering the correct part. This part is made of metal, and is sold individually. You may require a screwdriver to replace this item.

NEEDLE BEARING

$6.51

Fix Number: FIX12396288
Manufacturer Part Number: 093128-00

Included in part number 611971-00

Watch the install video

BRUSH

$12.35

Fix Number: FIX12410247
Manufacturer Part Number: 445861-25

(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.

Black and Decker Nibbler & Shears Parts

Popular Black and Decker Nibbler & Shears Parts

Installation Instructions

Black and Decker Nibbler & Shears Appliance Types

Popular Black and Decker Nibbler & Shears Models

Black and Decker Nibbler & Shears Parts

Start With Your Model Number

Popular Black and Decker Nibbler & Shears Parts

Installation Instructions

Black and Decker Nibbler & Shears Appliance Types

Popular Black and Decker Nibbler & Shears Models