Nibbler & Shears Parts

BRUSH SET

$13.60

Fix Number: FIX19505706
Manufacturer Part Number: 1619P11715

This brush set supplies electrical current to the motor by maintaining continuous contact with rotating components. Proper brush condition supports smooth motor operation, consistent power delivery, and reduced sparking. Replacing worn brushes helps restore motor efficiency, improves performance, and extends the life of the motor assembly.

Cutting Spring

$6.51

Fix Number: FIX10127843
Manufacturer Part Number: 40-50-0585

It is an authentic item that is made for use with Milwaukee copper tubing cutters. This component is supplied directly from the original equipment manufacturer. The spring is secured to the wheel axle and it applies tension on the cutting wheel. Over time it may wear out, lose tension or even break eventually requiring a replacement. One durable metal cutting spring is included. Make sure to refer to the appropriate diagrams and the owners manual of your model to ensure the correct replacement of this component. It is a simple repair that should not require any special tools.

CARBON BRUSH SET

$19.10

Fix Number: FIX19500981
Manufacturer Part Number: 160701417J

Carbon Brush CB-124 (Set of 2)

$12.74

★★★★★

1 Review

Fix Number: FIX10156640
Manufacturer Part Number: CB124

Carbon brushes are needed to conduct electricity to the armature through the commutator. The brushes are continuously rubbing against the rotating commutator, so will wear down over time, and will need to be replaced. If you are experiencing excessive sparks, this can also be caused by a damaged armature, so it is best to check it at the same time. This part includes two carbon brushes, which need to be replaced at the same time.

Shear Blade

$17.37

★★★★★

1 Review

Fix Number: FIX11928773
Manufacturer Part Number: 90590580-02

This is an OEM replacement shear blade. This is the complete blade assembly, which includes both the top and bottom cutters. This shear blade is specifically designed for trimming grass and weeds. Over time, the blades can dull or damage and will require replacement. This is a simple repair, that does not require any tools. You will remove the blade cover by pushing and holding the blade release button in the direction of the arrow. Slide the blade cover backwards and lift it off. While holding the blade onto the pins, locate and the blade cover and slide it forward.

Carbon Brush

$7.72

Fix Number: FIX10122198
Manufacturer Part Number: 22-18-0710

This carbon brush lead or also known as a carbon motor brush fits the following tools: angle grinders, nibbler and shears, sander polishers, and jig saws. This includes the brush and a wire lead attached. This is one of the most commonly replaced power tool components because the carbon brushes easily wear off with friction and use. If your brush is worn out it can cause intermittent motor function, reduction in electric braking, and in motor power. If you notice burns and cracks on the wire lead, then it is best to replace this part. Tip: when replacing your carbon brush, make sure to inspect your armature for damage as well, in case there are larger motor problems.

CARBON BRUSH SET

$8.89

Fix Number: FIX19500973
Manufacturer Part Number: 1607014144

This part includes two genuine carbon brushes with wire lead attached. If your motor is not performing smoothly, in most cases this is due to worn brushes. Carbon brushes are a common wear part that should be inspected and replaced on a regular schedule. Replace the carbon brushes if the wire lead has cracks or burns, and check the armature as well.

Switch Sgel 115cdy-6

$28.36

Fix Number: FIX10153603
Manufacturer Part Number: 651284-9

This is an OEM replacement part used with Makita sanders/routers. This switch is what allows user to turn the unit on and off. It is plastic a plastic switch with metal terminals. Over time mechanical moving components of a switch will begin to fail requiring a replacement. Please note this item is sold individually. To complete this repair you will need a screwdriver. • Remove housing • Disconnect wires • Remove old switch • Install new switch • Re-attach wires • Reassemble and test the unit

Watch the install video

BRUSH

$11.19

Fix Number: FIX12410247
Manufacturer Part Number: 445861-25

(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.

Carbon Brush

$7.91

★★★★★

1 Review

Fix Number: FIX10156666
Manufacturer Part Number: CB458

This part includes two OEM carbon brushes with the wire leads attached. Your tools motor requires two carbon brushes to create electricity for the armature. It is common for the carbon brushes to wear down over time, and this is why it is important to continually inspect them and replace them as part of your regular maintenance. If you notice sparks around the commutator, this may indicate a worn brush or a damaged armature, so we recommend inspecting both. To access this part you will need to remove the rear cover.

Installation Instructions

Gary from AVON PARK, FL

Armature was shorted (Used only three times)

Disassembly is simple enough but please remove the brushes before pulling out the armature. It is imperative as the commutator ring will catch on the brushes otherwise. Slipped in the new armature and installed the new brushes and reassembled. Runs smoothly and performs as expected. Old brushes were not worn at all as it was used very little but installed new ones anyway. Read more...

Popular Nibbler & Shears Parts

Installation Instructions

Nibbler & Shears Brands

Popular Nibbler & Shears Models

Nibbler & Shears Parts

Start With Your Model Number

Popular Nibbler & Shears Parts

Installation Instructions

Nibbler & Shears Brands

Popular Nibbler & Shears Models